Mac Developer Library Developer


This manual page is for Mac OS X version 10.9

If you are running a different version of Mac OS X, view the documentation locally:

  • In Terminal, using the man(1) command

Reading manual pages

Manual pages are intended as a quick reference for people who already understand a technology.

  • To learn how the manual is organized or to learn about command syntax, read the manual page for manpages(5).

  • For more information about this technology, look for other documentation in the Apple Developer Library.

  • For general information about writing shell scripts, read Shell Scripting Primer.

CONFIG(5)                                          OpenSSL                                         CONFIG(5)

       config - OpenSSL CONF library configuration files

       The OpenSSL CONF library can be used to read configuration files.  It is used for the OpenSSL master
       configuration file openssl.cnf and in a few other places like SPKAC files and certificate extension
       files for the x509 utility. OpenSSL applications can also use the CONF library for their own

       A configuration file is divided into a number of sections. Each section starts with a line [
       section_name ] and ends when a new section is started or end of file is reached. A section name can
       consist of alphanumeric characters and underscores.

       The first section of a configuration file is special and is referred to as the default section this
       is usually unnamed and is from the start of file until the first named section. When a name is being
       looked up it is first looked up in a named section (if any) and then the default section.

       The environment is mapped onto a section called ENV.

       Comments can be included by preceding them with the # character

       Each section in a configuration file consists of a number of name and value pairs of the form

       The name string can contain any alphanumeric characters as well as a few punctuation symbols such as
       . , ; and _.

       The value string consists of the string following the = character until end of line with any leading
       and trailing white space removed.

       The value string undergoes variable expansion. This can be done by including the form $var or ${var}:
       this will substitute the value of the named variable in the current section. It is also possible to
       substitute a value from another section using the syntax $section::name or ${section::name}. By using
       the form $ENV::name environment variables can be substituted. It is also possible to assign values to
       environment variables by using the name ENV::name, this will work if the program looks up environment
       variables using the CONF library instead of calling getenv() directly.

       It is possible to escape certain characters by using any kind of quote or the \ character. By making
       the last character of a line a \ a value string can be spread across multiple lines. In addition the
       sequences \n, \r, \b and \t are recognized.

       In OpenSSL 0.9.7 and later applications can automatically configure certain aspects of OpenSSL using
       the master OpenSSL configuration file, or optionally an alternative configuration file. The openssl
       utility includes this functionality: any sub command uses the master OpenSSL configuration file
       unless an option is used in the sub command to use an alternative configuration file.

       To enable library configuration the default section needs to contain an appropriate line which points
       to the main configuration section. The default name is openssl_conf which is used by the openssl
       utility. Other applications may use an alternative name such as myapplicaton_conf.

       The configuration section should consist of a set of name value pairs which contain specific module
       configuration information. The name represents the name of the configuration module the meaning of
       the value is module specific: it may, for example, represent a further configuration section
       containing configuration module specific information. E.g.

        openssl_conf = openssl_init


        oid_section = new_oids
        engines = engine_section


        ... new oids here ...


        ... engine stuff here ...

       Currently there are two configuration modules. One for ASN1 objects another for ENGINE configuration.

       This module has the name oid_section. The value of this variable points to a section containing name
       value pairs of OIDs: the name is the OID short and long name, the value is the numerical form of the
       OID. Although some of the openssl utility sub commands already have their own ASN1 OBJECT section
       functionality not all do. By using the ASN1 OBJECT configuration module all the openssl utility sub
       commands can see the new objects as well as any compliant applications. For example:


        some_new_oid =
        some_other_oid =

       In OpenSSL 0.9.8 it is also possible to set the value to the long name followed by a comma and the
       numerical OID form. For example:

        shortName = some object long name,

       This ENGINE configuration module has the name engines. The value of this variable points to a section
       containing further ENGINE configuration information.

       The section pointed to by engines is a table of engine names (though see engine_id below) and further
       sections containing configuration informations specific to each ENGINE.

       Each ENGINE specific section is used to set default algorithms, load dynamic, perform initialization
       and send ctrls. The actual operation performed depends on the command name which is the name of the
       name value pair. The currently supported commands are listed below.

       For example:


        # Configure ENGINE named "foo"
        foo = foo_section
        # Configure ENGINE named "bar"
        bar = bar_section

        ... foo ENGINE specific commands ...

        ... "bar" ENGINE specific commands ...

       The command engine_id is used to give the ENGINE name. If used this command must be first. For

        # This would normally handle an ENGINE named "foo"
        foo = foo_section

        # Override default name and use "myfoo" instead.
        engine_id = myfoo

       The command dynamic_path loads and adds an ENGINE from the given path. It is equivalent to sending
       the ctrls SO_PATH with the path argument followed by LIST_ADD with value 2 and LOAD to the dynamic
       ENGINE. If this is not the required behaviour then alternative ctrls can be sent directly to the
       dynamic ENGINE using ctrl commands.

       The command init determines whether to initialize the ENGINE. If the value is 0 the ENGINE will not
       be initialized, if 1 and attempt it made to initialized the ENGINE immediately. If the init command
       is not present then an attempt will be made to initialize the ENGINE after all commands in its
       section have been processed.

       The command default_algorithms sets the default algorithms an ENGINE will supply using the functions

       If the name matches none of the above command names it is assumed to be a ctrl command which is sent
       to the ENGINE. The value of the command is the argument to the ctrl command. If the value is the
       string EMPTY then no value is sent to the command.

       For example:


        # Configure ENGINE named "foo"
        foo = foo_section

        # Load engine from DSO
        dynamic_path = /some/path/
        # A foo specific ctrl.
        some_ctrl = some_value
        # Another ctrl that doesn't take a value.
        other_ctrl = EMPTY
        # Supply all default algorithms
        default_algorithms = ALL

       If a configuration file attempts to expand a variable that doesn't exist then an error is flagged and
       the file will not load. This can happen if an attempt is made to expand an environment variable that
       doesn't exist. For example in a previous version of OpenSSL the default OpenSSL master configuration
       file used the value of HOME which may not be defined on non Unix systems and would cause an error.

       This can be worked around by including a default section to provide a default value: then if the
       environment lookup fails the default value will be used instead. For this to work properly the
       default value must be defined earlier in the configuration file than the expansion. See the EXAMPLES
       section for an example of how to do this.

       If the same variable exists in the same section then all but the last value will be silently ignored.
       In certain circumstances such as with DNs the same field may occur multiple times. This is usually
       worked around by ignoring any characters before an initial . e.g.

        1.OU="My first OU"
        2.OU="My Second OU"

       Here is a sample configuration file using some of the features mentioned above.

        # This is the default section.

        RANDFILE= ${ENV::HOME}/.rnd

        [ section_one ]

        # We are now in section one.

        # Quotes permit leading and trailing whitespace
        any = " any variable name "

        other = A string that can \
        cover several lines \
        by including \\ characters

        message = Hello World\n

        [ section_two ]

        greeting = $section_one::message

       This next example shows how to expand environment variables safely.

       Suppose you want a variable called tmpfile to refer to a temporary filename. The directory it is
       placed in can determined by the the TEMP or TMP environment variables but they may not be set to any
       value at all. If you just include the environment variable names and the variable doesn't exist then
       this will cause an error when an attempt is made to load the configuration file. By making use of the
       default section both values can be looked up with TEMP taking priority and /tmp used if neither is

        # The above value is used if TMP isn't in the environment
        # The above value is used if TEMP isn't in the environment

       Currently there is no way to include characters using the octal \nnn form. Strings are all null
       terminated so nulls cannot form part of the value.

       The escaping isn't quite right: if you want to use sequences like \n you can't use any quote escaping
       on the same line.

       Files are loaded in a single pass. This means that an variable expansion will only work if the
       variables referenced are defined earlier in the file.

       x5_9(1), req(1), ca(1)

50                                               2013-03-05                                        CONFIG(5)

Reporting Problems

The way to report a problem with this manual page depends on the type of problem:

Content errors
Report errors in the content of this documentation to the OpenSSL project by sending email to
Bug reports
Report bugs in the functionality of the described tool or API to Apple through Bug Reporter and to the OpenSSL project by sending email to
Formatting problems
Report formatting mistakes in the online version of these pages with the feedback links below.