Understand the role of drivers in bridging the gap between software and hardware, ensuring smooth hardware functionality.

Drivers Documentation

Posts under Drivers subtopic

Post

Replies

Boosts

Views

Activity

[DEXT Migration Issue] IOUserSCSIParallelInterfaceController fails to handle low-level I/O from `diskutil`
Hello everyone, We are migrating our KEXT for a Thunderbolt storage device to a DEXT based on IOUserSCSIParallelInterfaceController. We've run into a fundamental issue where the driver's behavior splits based on the I/O source: high-level I/O from the file system (e.g., Finder, cp) is mostly functional (with a minor ls -al sorting issue for Traditional Chinese filenames), while low-level I/O directly to the block device (e.g., diskutil) fails or acts unreliably. Basic read/write with dd appears to be mostly functional. We suspect that our DEXT is failing to correctly register its full device "personality" with the I/O Kit framework, unlike its KEXT counterpart. As a result, low-level I/O requests with special attributes (like cache synchronization) sent by diskutil are not being handled correctly by the IOUserSCSIParallelInterfaceController framework of our DEXT. Actions Performed & Relevant Logs 1. Discrepancy: diskutil info Shows Different Device Identities for DEXT vs. KEXT For the exact same hardware, the KEXT and DEXT are identified by the system as two different protocols. KEXT Environment: Device Identifier: disk5 Protocol: Fibre Channel Interface ... Disk Size: 66.0 TB Device Block Size: 512 Bytes DEXT Environment: Device Identifier: disk5 Protocol: SCSI SCSI Domain ID: 2 SCSI Target ID: 0 ... Disk Size: 66.0 TB Device Block Size: 512 Bytes 2. Divergent I/O Behavior: Partial Success with Finder/cp vs. Failure with diskutil High-Level I/O (Partially Successful): In the DEXT environment, if we operate on an existing volume (e.g., /Volumes/MyVolume), file copy operations using Finder or cp succeed. Furthermore, the logs we've placed in our single I/O entry point, UserProcessParallelTask_Impl, are triggered. Side Effect: However, running ls -al on such a volume shows an incorrect sorting order for files with Traditional Chinese names (they appear before . and ..). Low-Level I/O (Contradictory Behavior): In the DEXT environment, when we operate directly on the raw block device (/dev/disk5): diskutil partitionDisk ... -> Fails 100% of the time with the error: Error: -69825: Wiping volume data to prevent future accidental probing failed. dd command -> Basic read/write operations appear to work correctly (a write can be immediately followed by a read within the same DEXT session, and the data is correct). 3. Evidence of Cache Synchronization Failure (Non-deterministic Behavior) The success of the dd command is not deterministic. Cross-environment tests prove that its write operations are unreliable: First Test: In the DEXT environment, write a file with random data to /dev/disk5 using dd. Reboot into the KEXT environment. Read the data back from /dev/disk5 using dd. The result is a file filled with all zeros. Conclusion: The write operation only went to the hardware cache, and the data was lost upon reboot. Second Test: In the DEXT environment, write the same random file to /dev/disk5 using dd. Key Variable: Immediately after, still within the DEXT environment, read the data back once for verification. The content is correct! Reboot into the KEXT environment. Read the data back from /dev/disk5. This time, the content is correct! Conclusion: The additional read operation in the second test unintentionally triggered a hardware cache flush. This proves that the dd (in our DEXT) write operation by itself does not guarantee synchronization, making its behavior unreliable. Our Problem Based on the observations above, we have the conclusion: High-Level Path (triggered by Finder/cp): When an I/O request originates from the high-level file system, the framework seems to enter a fully-featured mode. In this mode, all SCSI commands, including READ/WRITE, INQUIRY, and SYNCHRONIZE CACHE, are correctly packaged and dispatched to our UserProcessParallelTask_Impl entry point. Therefore, Finder operations are mostly functional. Low-Level Path (triggered by dd/diskutil): When an I/O request originates from the low-level raw block device layer: The most basic READ/WRITE commands can be dispatched (which is why dd appears to work). However, critical management commands, such as INQUIRY and SYNCHRONIZE CACHE, are not being correctly dispatched or handled. This leads to the incorrect device identification in diskutil info and the failure of diskutil partitionDisk due to its inability to confirm cache synchronization. We would greatly appreciate any guidance, suggestions, or insights on how to resolve this discrepancy. Specifically, what is the recommended approach within DriverKit to ensure that a DEXT based on IOUserSCSIParallelInterfaceController can properly declare its capabilities and handle both high-level and low-level I/O requests uniformly? Thank you. Charles
12
0
2.5k
Jul ’26
Automate system extensions installation
Hello, We are running some tests with our driver with SIP on. We have all the entitlements and everything works smoothly. Thing is, when we run our xxxx.app from Applications, it pops up a GUI with install and uninstall button that we created. When we do install, it prompts us to enable system extension in System settings. I am wondering if there is a way to automate this. I understand I can automate running the xxxx.app from command line but can we automate having to go to System settings->login items & Extensions and enabling our system extension from command line too. Does Apple force an user to go to settings and do it once for security? From my research, I did not find any reliable answer to this. Thank you for your help!
1
0
1.6k
Jul ’26
DriverKit VLAN offload: IOUserNetworkPacket::getVlanTag() always returns false, kFeatureHardwareVlan undocumented
I've built an open-source DriverKit + NetworkingDriverKit (IOUserNetworkEthernet/Skywalk) driver for a USB 5GbE adapter (AQTION AQC111U chipset). As far as I can tell this is the first public one for real third-party hardware: github.com/jquirke/AQC111Driver It's a fully functional driver at this point: RX/TX hardware checksum offload, jumbo frame/MTU control up to 16KB, runtime-controllable diagnostics via a custom IOUserClient, and most recently working 802.1Q VLAN support via macOS's vlan(4) software path. While attempting to implement hardware offload VLAN support, I ran into what looks like a gap between documentation and the public SDK, and I'd appreciate expert opinion either way before filing Feedback. The issue: IOUserNetworkPacket::getVlanTag()/setVlanTag() (DriverKit 24.0+) have a doc comment stating: "Get the Vlan Tag from the packet, where the driver has enabled the kFeatureHardwareVlan capability; for the case that feature is not enabled, this method will return false." kFeatureHardwareVlan does not appear anywhere in the public NetworkingDriverKit.framework/Headers/ tree confirmed via exhaustive grep, including the full hwAssist/feature-flag enum in IOUserNetworkTypes.h. I tested every plausible related mechanism exhaustively, with a real device reattach for each combination, to rule out attach-time-only behaviour: +------------------------+--------------------------+--------------+-----------+ | HWAssist bit declared? | SetSoftwareVlanSupport()| getVlanTag() | vlan0 MTU | +------------------------+--------------------------+--------------+-----------+ | Yes | true | always false | 1500 | | Yes | false | always false | 1500 | | No | not called | always false | 1496 | | No | false | always false | 1496 | +------------------------+--------------------------+--------------+-----------+ none of these combinations gates real 802.1q tag-delivery/demux behavior at all; it seems Vlan support is completely implemented in software on the MacOS side and I have to explicitly program my hardware registers to disable VLAN tagging. Question: is hardware VLAN tag insert/strip (via getVlanTag()/setVlanTag()) currently reachable from a third-party DriverKit USB Ethernet driver at all? If kFeatureHardwareVlan is real but intentionally withheld from public headers, is there a documented path (entitlement, different NDK version, etc.) to enable it or is this confirmed unreachable without Apple's direct involvement (Feedback/DTS)? Can share full test logs/methodology if useful.
2
2
1.7k
Jul ’26
Entitlements received only for vendor ID. Is this normal?
Hi, I recently requested for some entitlements from Apple. In the form that I filled, there was only placeholder for Vendor ID so I put my vendor ID (in decimals). There was no placeholder to specify Device ID. However, in the Description placeholder at the end of the form, I did put the device ID (in decimals). After I got the entitlements, I tried loading my driver to match the device. It does match with only vendor ID but does not match with Vendor and Device ID together. So, now matching has widened little bit more than what we wanted. I was wondering if this is normal or if I did something wrong due to which entitlements was only granted for vendor ID but not for vendor + device Id. Thank you for your time!
1
0
1.7k
Jul ’26
[iOS 26] thermalmonitord cpu-avg-limiter-input-w2r read failure + SPMI bus faults on iPhone 15 Pro (A17 Pro) — likely driver regression
Since upgrading to iOS 26, my iPhone 15 Pro (A17 Pro) exhibits persistent battery drain and thermal issues. Console.app analysis via Mac reveals a cluster of related kernel and daemon errors that appear to stem from a driver-level regression rather than a hardware fault. Observed errors (continuous, since boot): thermalmonitord fails to read the cpu-avg-limiter-input-w2r property every 5 seconds indefinitely. This leaves the thermal throttling subsystem unable to regulate CPU load using its primary input sensor. The kernel logs SPMI bus faults on nub-spmi1 at a perfectly regular 30-second interval (codes 0x72040C01, 0x75E40C3B, 0x72D80C33), alongside aop-spmi0 faults (0x7A000830). The strict periodicity strongly suggests a driver retry loop rather than a dead hardware component. appleh16camerad (ISP driver) fails to initialize endpoint 1 (fISPEndpoints[1] is not ready) and retries every ~4 seconds, while the ANE driver (ANE0) cannot register its memory unwire timer. Both run in permanent retry loops consuming CPU cycles. AppleSMCFamily logs kSMCKeyNotWritable errors on SMC write attempts — the key exists but is flagged non-writable, suggesting incomplete driver initialization rather than a missing component. A single AppleSARService coredump request for the baseband was also observed. Why this appears to be a driver issue and not hardware: The system remains stable with no kernel panics or forced reboots. The SPMI faults occur on a precise 30-second schedule consistent with a kernel timer, not random hardware failures. The SMC error is kSMCKeyNotWritable (key present, wrong state) rather than kSMCKeyNotFound. All symptoms appeared immediately after the iOS 26 update with no physical event on the device. Device: iPhone 15 Pro — A17 Pro iOS version: 26.0 Reproduced: persistent across reboots, not tied to any specific app or usage pattern Has anyone observed the same pattern on A17 Pro devices? And has Apple acknowledged any SPMI / thermalmonitord regression in iOS 26 for this chip family?
3
1
1.6k
Jul ’26
DriverKit kernel crash, possible PCI bridge issue?
DriverKit kernel crash, possible PCI bridge issue? In working on a DriverKit driver for a legacy SCSI controller, we have finally arrived at the expected (and usually joyful) point in driver development - a repeatable kernel crash and reboot. It happens when the controller first attempts to do "real work" by accessing requests or replies provided to it by the driver. I will provide additional information below (and can share more), but it’s a bit tricky because there is a lot of steps required to get to the point where the PCIe card is sufficiently initialized to respond, presumably attempt a memory access, and bring down the whole system. The system freezes and reboots write after the first MemoryWrite32 with an address of a request. The address is properly (we believe) mapped, using IODMACommand et al, approximately like so: uint64_t reqArrSize = MPT_REQUEST_AREA * kMaxTasks; IOAddressSegment arrseg = {}; IOMemoryMap * arrmap = nullptr; ret = IOBufferMemoryDescriptor::Create(kIOMemoryDirectionInOut, reqArrSize, 0, &ivars->fReqArrayDesc); if (ret != kIOReturnSuccess) { … } IODMACommandSpecification dmaspec = {}; dmaspec.options = kIODMACommandSpecificationNoOptions; dmaspec.maxAddressBits = 32; // tried 31 here but that fails to allocate, the addresses start at 80000000, then leads to a crash // but that seems to be a bridge / SID issue, not the address itself ret = IODMACommand::Create(ivars->pciDevice, kIODMACommandCreateNoOptions, &dmaspec, &ivars->fReqArrayDMA); if (ret != kIOReturnSuccess) { … } ivars->fReqArrayDMA->retain(); uint64_t dmaFlags = 0; uint32_t segCount = 1; // capacity in; actual out IOAddressSegment segs[1] = {}; ret = ivars->fReqArrayDMA->PrepareForDMA(kIODMACommandPrepareForDMANoOptions, ivars->fReqArrayDesc, 0, reqArrSize, &dmaFlags, &segCount, segs); if ((ret != kIOReturnSuccess ) || (segCount != 1)) {…} ivars->fReqArrayPhys = segs[0].address; ivars->fReqArrayDesc->CreateMapping(0,0,0,0,0, &arrmap); // virtual mapping ivars->fReqArray = (uint8_t *)(arrmap ? arrmap->GetAddress() : 0); // virtual ivars->fReqFreemap.set(); // mark all request entries as free memset(ivars->fReqArray, 0, reqArrSize); The crash is very violent and consistent: panic(...): "dart-apciec0 (...): DART DART exception SID 0 ERROR_STATUS 0x80000001 ERROR_ADDRESS 0x0000000080000000 (no exceptionInfo)" @AppleT8110DART.cpp:1720 The fault address is the address we write to one of the controller's control register. We suspect that the issue is that this card uses an 8114 bridge, which uses its SID for the request, instead of the (scsi controller chip) endpoint. The mapping, meanwhile, is under the endpoint’s SID. So when the controller attempts its first request using the physical address, the mapping does not exist at the right level - which brings down the whole system. pcic0-bridge 0x106b/0x1015 Apple TB PCIe port └ pci-bridge 0x1b21/0x2461 ASMedia (TB tunnel) └ pci-bridge 0x1b21/0x2461 ASMedia IOPCITunnelled=Yes └ pci-bridge 0x10b5/0x8114 - (on the controller card) PLX PEX 8114, PCIe-to-PCI-X bridge └ scsi@8 0x1000/0x0030 - (on the controller card), LSI, on bus 4 (PCI-X secondary side) Worse yet, there appears to be no way form within a DEXT to ask for a mapping at a different level, and the 8114 doesn’t have a mapper of its own anyway (attempting to do so with a separate DEXT fails). That last part we know because we tried a workaround with two DEXTs, one that successfully matches the 8114 bridge and the other that matches the SCSI controller chip itself. However, the bridge doesn’t have a mapper attached and so the OS does not seem to give us a useful address (using the same IOBufferMemoryDescriptor::Create, ODMACommand::Create, PrepareForDMA sequence), and 32 bit request simply fails with kIOReturnMessageTooLarge. Attached is a quick diagram of our suspicions and a longer write-up (far warning, unlike the above, that is mostly AI output but it’s been reviewed by the team). Questions: Have others dealt with this problem of legacy PCI devices that have bridges that don’t fit neatly into the restrictions, and what did you do? Is there a way to get the right virtual<->physical mappings recognized at the right level? Is there a way to temporarily turn off SID checking or is that (as I assume) intrinsic to how this works? Are we on the wrong track entirely?
1
0
1.6k
Jul ’26
Reboot-free upgrade of an always-matched DriverKit dext
I have a DriverKit dext that implements a virtual SCSI HBA (no physical hardware). Because a bare IOUserSCSIParallelInterfaceController has no provider to match, the bundle ships two IOKitPersonalities: Bootstrap — IOClass IOUserService, IOProviderClass IOUserResources, IOResourceMatch IOKit. In Start() it does SetProperties({NvmeOfSCSIHBA: true}) + RegisterService(), publishing itself as a nub. Controller — IOClass IOUserSCSIParallelInterfaceController, IOProviderClass IOUserService, IOPropertyMatch {NvmeOfSCSIHBA: true} — it matches the bootstrap nub. This loads and runs correctly. The problem is upgrades. Activating a higher CFBundleVersion via OSSystemExtensionRequest.activationRequest (in-place replace) always defers the old version's termination to reboot. The new version reaches [activated enabled] but never starts; the old process keeps running until reboot. From sysextd/kernelmanagerd: kernelmanagerd Dext … v15 … is being replaced and cannot be terminated right away sysextd delegate returns Error Domain=OSSystemExtensionErrorDomain Code=101 "…is being replaced", assumes responsibility for old version …, keeping old version 15 sysextd turning the responsibility for termination of …, version 15 over to delegate (with uninstallation at the next reboot) sysextd a category delegate declined to terminate extension with identifier: … sysextd v15 terminating_for_uninstall → terminating_for_upgrade_via_delegate Key observation: this defers even on a fresh boot where the dext was never opened — no app/daemon ever opened the IOUserClient, no I/O, nothing attached beyond the controller↔nub match. So it does not appear to be a "client still holds it open" / busy-state situation; the driver_extension category delegate declines the moment it's a replacement. What I've tried: In-place activationRequest (replace): always defers to reboot (above). deactivationRequest (standalone): the request hangs — no delegate callback at all (waited ~13 min), even with no client open. Disconnecting all clients first (graceful Stop() that cancels its dispatch queues and completes async) does not change the replace deferral. My understanding from the docs/forums is that the normal reboot-free replace relies on the backing device being disconnected/reconnected to quiesce the old dext (thread 677040). My controller matches a persistent IOUserResources-backed nub that never detaches, so there's no equivalent quiesce point. Questions: For a dext whose only provider is a self-published IOUserResources nub (no detachable hardware), is reboot-free replacement structurally impossible — i.e. is the Code=101 "is being replaced" defer inherent to this matching pattern? Is the supported way to live-upgrade such a dext to deactivationRequest → (on .completed) → activationRequest rather than an in-place replace? If so, what makes a deactivationRequest complete in-session vs. defer to reboot for an IOUserResources-matched dext — and what would cause it to hang with no delegate callback? (Daemon's IOUserClient is closed; the controller's Stop() cancels its queues and completes.) Should the dext itself proactively tear down the published nub (e.g. terminate the bootstrap IOService) before/at upgrade so the controller detaches — or does that just re-match the still-staged old personalities and relaunch the old version? Is there a recommended pattern for a virtual (hardwareless) DriverKit HBA that needs in-field, reboot-free version updates, or is reboot genuinely required for this class of dext? Environment: macOS 27 (Tahoe)
1
0
1.4k
Jul ’26
Latency critical DMA read via PCIe
Dear All, I am currently developing a high throughput audio system which operates via PCIe tunneled into a USB4 interface. This include a custom FPGA based hardware and custom Audio DriverKit driver. While performing read operation via the hw DMA (that is a Host to Device transfer), I am noticing sparse latency spikes into the read transfers. Specifically, 4KB operations (which I assume including MRd + CpID) take normally from 5us to 40us to be completed, perfectly fine for my case. However, in some rare occasions, they can end up to 400us, which causes me overruns. The measurements have been carried out from the FPGA and they include the overall request and transfer time. While trying to tackle the problem, I'm investigating the possible power saving options and performance constraint methods at my disposal. I currently use these methods to mitigate the problem. ChangePowerState(kIOServicePowerCapabilityOn); SetPowerOverride(true); RequireMaxBusStall(kIOMaxBusStall25usec); CreatePMAssertion(kIOServicePMAssertionCPUBit | kIOServicePMAssertionForceFullWakeupBit, &ivars->PMAssertionID, false); The buffers are currently about 16MB, single segment, 16KB aligned and, of course, "prepared" for DMA. The system run for 3 hours without any overrun, but I'm not still fully convinced about its reliability. May someone provide me some comments on this? Are there profiling tools that I can use? Feel free to request me any required detail. The testing system is a MacBook Pro M2 Pro. Many Thanks and Best Regards Francesco
9
0
1.6k
Jun ’26
Reboot-free upgrade of an always-matched DriverKit dext
I have a DriverKit dext that implements a virtual SCSI HBA (no physical hardware). Because a bare IOUserSCSIParallelInterfaceController has no provider to match, the bundle ships two IOKitPersonalities: Bootstrap — IOClass IOUserService, IOProviderClass IOUserResources, IOResourceMatch IOKit. In Start() it does SetProperties({NvmeOfSCSIHBA: true}) + RegisterService(), publishing itself as a nub. Controller — IOClass IOUserSCSIParallelInterfaceController, IOProviderClass IOUserService, IOPropertyMatch {NvmeOfSCSIHBA: true} — it matches the bootstrap nub. This loads and runs correctly. The problem is upgrades. Activating a higher CFBundleVersion via OSSystemExtensionRequest.activationRequest (in-place replace) always defers the old version's termination to reboot. The new version reaches [activated enabled] but never starts; the old process keeps running until reboot. From sysextd/kernelmanagerd: kernelmanagerd Dext … v15 … is being replaced and cannot be terminated right away sysextd delegate returns Error Domain=OSSystemExtensionErrorDomain Code=101 "…is being replaced", assumes responsibility for old version …, keeping old version 15 sysextd turning the responsibility for termination of …, version 15 over to delegate (with uninstallation at the next reboot) sysextd a category delegate declined to terminate extension with identifier: … sysextd v15 terminating_for_uninstall → terminating_for_upgrade_via_delegate Key observation: this defers even on a fresh boot where the dext was never opened — no app/daemon ever opened the IOUserClient, no I/O, nothing attached beyond the controller↔nub match. So it does not appear to be a "client still holds it open" / busy-state situation; the driver_extension category delegate declines the moment it's a replacement. What I've tried: In-place activationRequest (replace): always defers to reboot (above). deactivationRequest (standalone): the request hangs — no delegate callback at all (waited ~13 min), even with no client open. Disconnecting all clients first (graceful Stop() that cancels its dispatch queues and completes async) does not change the replace deferral. My understanding from the docs/forums is that the normal reboot-free replace relies on the backing device being disconnected/reconnected to quiesce the old dext (thread 677040). My controller matches a persistent IOUserResources-backed nub that never detaches, so there's no equivalent quiesce point. Questions: For a dext whose only provider is a self-published IOUserResources nub (no detachable hardware), is reboot-free replacement structurally impossible — i.e. is the Code=101 "is being replaced" defer inherent to this matching pattern? Is the supported way to live-upgrade such a dext to deactivationRequest → (on .completed) → activationRequest rather than an in-place replace? If so, what makes a deactivationRequest complete in-session vs. defer to reboot for an IOUserResources-matched dext — and what would cause it to hang with no delegate callback? (Daemon's IOUserClient is closed; the controller's Stop() cancels its queues and completes.) Should the dext itself proactively tear down the published nub (e.g. terminate the bootstrap IOService) before/at upgrade so the controller detaches — or does that just re-match the still-staged old personalities and relaunch the old version? Is there a recommended pattern for a virtual (hardwareless) DriverKit HBA that needs in-field, reboot-free version updates, or is reboot genuinely required for this class of dext? Environment: macOS 27 (Tahoe)
0
0
1.1k
Jun ’26
Supported way to expose an iPhone+controller as a macOS gamepad without restricted entitlements?
I’m prototyping a personal-use system that lets an iPhone with a physically attached controller act as an input device for a Mac. End goal: Use the iPhone as the transport and sensor host Use the attached physical controller for buttons/sticks Map the iPhone gyroscope to the controller’s right stick to get gyro aim in Mac games / cloud-streamed games such as GeForce NOW that don't support the gyro. What I’m trying to understand is whether Apple supports any path for this on macOS that does NOT require restricted entitlements or paid-program-only capabilities. What I’ve already found: CoreHID virtual HID device creation appears to require com.apple.developer.hid.virtual.device HIDDriverKit / system extensions appear to require Apple-granted entitlements as well GCVirtualController does not seem to solve the problem because I need a controller-visible device that other apps can see, not just controls inside my own app So my concrete question is: Is there any supported, entitlement-free way for a personal macOS app to expose a game-controller-like input device that other apps can consume system-wide? If not, is the official answer that this class of solution necessarily requires one of: CoreHID with restricted entitlement HIDDriverKit/system extension entitlement some other Apple-approved framework or program I’m missing I’m not asking about App Store distribution. This is primarily for local/personal use during development. I’m trying to understand the supported platform boundary before investing further. Any guidance on the recommended architecture for this use case would be appreciated.
4
1
2.3k
Jun ’26
HAL Plugin (AudioServerPlugin) — Plugin_StartIO never called from AUHAL input client
I'm building a virtual audio device using the HAL Plugin (AudioServerPlugin) API on macOS. The plugin loads correctly, WriteMix is called with non-zero audio data, but Plugin_StartIO is never called from my app's AUHAL input client. Environment: macOS 26.5 Xcode (latest) Bundle ID: com.private.SubON Plugin installed at: /Library/Audio/Plug-Ins/HAL/SubONHALPlugin.driver What works: Plugin loads and is visible as "SubON Virtual Device" Plugin_AddDeviceClient is called with bundleID=com.private.SubON WriteMix is called with non-zero maxSrc values (audio is reaching the plugin) AUHAL setup completes: EnableIO input=1 output=0, CurrentDevice set correctly, AudioUnitInitialize succeeds pre-start readback confirms: currentDevice matches, enableIOIn=1 What doesn't work: Plugin_StartIO is never called from the SubON.app input client WillDoIOOperation is never called ReadInput is never called maxAmplitude in the input tap is always 0.0 AUHAL setup code (Swift): AudioUnitUninitialize(auhal) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_EnableIO, kAudioUnitScope_Input, 1, &one, size) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_EnableIO, kAudioUnitScope_Output, 0, &zero, size) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_CurrentDevice, kAudioUnitScope_Global, 0, &deviceID, size) AudioUnitInitialize(auhal) HAL Plugin — WillDoIOOperation: outWillDo = true; outWillDoInPlace = true; Returns true for both ReadInput and WriteMix. Observation: Even when selecting "SubON Virtual Device" as the system input device in System Settings, Plugin_StartIO is still never called. Any ideas what could prevent Plugin_StartIO from being called despite AUHAL configuration appearing correct?
0
0
1.6k
Jun ’26
Simple question on
Hopefully a very quick question for anyone familiar with IOUserSCSIParallelInterfaceController - what is the right initialization to implement: init () override; Start (IOService * provider) override; UserInitializeController () override; something else Seems #3 is required, but guidance varies on the others, undoubtedly bc IOUserSCSI.. implements a lot of things beyond the usual DriverKit structure. Thanks in advance for any help. (We're trying to implement a driver for a legacy SCSI controller).
3
0
1.2k
Jun ’26
iPad USB-C (serial communication) by cable
Hello, I have a device like a gas meter or an electricity meter and it has: an optical interface IEC 62056-21 (IEC-1107) with support for speeds up to 115,200 Bd. On Windows and Android, we use a cable that has an optical interface and on the other end we connect USB A to the PC and to the Android via an OTG to USB adapter. The cable contains a chip from FTDI FT230XQ. I have an application in MAUI where I want to connect this cable to the 10th generation iPad and communicate similarly to, for example, via the COM5 port on the PC. When the port opens, I send a query and get a response. Is it possible, what should I do for this? What about Apple certification of cables? Is it possible to send a packet from MAUI via the USB C port via the cable and then receive and process the packet again? What about MFi? I found this: https://redpark.com/usb-c-serial-cable/ Please can you give me some idea or expert to this topic? Thanks, Roman
1
0
1.1k
Jun ’26
Our driver next fails due to DriverKit attempting to call
We are developing an IOUserSCSIParallelInterfaceController driver for a legacy controller. After completing init() successfully, no other methods are called before a DriverKit assert failure - .driver.dext) Assertion failed: (notsync || !remote || (msgid == IOService_Start_ID) || queue->OnQueue()), function Invoke, file uioserver.cpp, line 1654. - that leads immediately to "IOPCIDevice::ClientCrashed_Impl() for client " . This appears to be because the framework is attempting a SetPowerState()' during DEXT load, which is delivered off-queue and panics in OSMetaClassBase::Invoke (uioserver.cpp`) before any other dext method runs. Apple Silicon Mac, macOS 26 (DriverKit 25.1 SDK), Xcode 26.x. Expected: The SetPowerState() power-up is delivered on the driver object's dispatch queue (or otherwise handled by the framework), allowing the dext's SetPowerState override to run, ACK via super::SetPowerState(powerFlags, SUPERDISPATCH), and proceed to UserInitializeController. Actual behavior: init() completes (our trace logs init then completed init) Neither Start_Impl nor SetPowerState_Impl ever executes Instead the process fails with the assertion above , IOPCIDevice::ClientCrashed_Impl() reports "client … does not have open session … skipping recovery". The dext crash-loops ("Driver … has crashed N time(s)"). Any suggestions?
5
0
1.4k
Jun ’26
How to deliver a USBDriverKit driver in an SDK or Framework for sale to third parties?
I have a product that currently communicates to a piece of proprietary Medical hardware via USB. We have a driver created with USBDriverKit that is a hard requirement for this product to function. Currently, we are delivering an iPadOS application that utilizes the driver. Our next step is to create an SDK that includes all of the Frameworks and the driver utilized by the application. Since the driver is a system extension that lives in the application, how do we bundle it with our SDK and make it available for use by third-parties?
5
0
1.8k
Jun ’26
System Panic with IOUserSCSIParallelInterfaceController during Dispatch Queue Configuration
Hello everyone, We are in the process of migrating a high-performance storage KEXT to DriverKit. During our initial validation phase, we noticed a performance gap between the DEXT and the KEXT, which prompted us to try and optimize our I/O handling process. Background and Motivation: Our test hardware is a RAID 0 array of two HDDs. According to AJA System Test, our legacy KEXT achieves a write speed of about 645 MB/s on this hardware, whereas the new DEXT reaches about 565 MB/s. We suspect the primary reason for this performance gap might be that the DEXT, by default, uses a serial work-loop to submit I/O commands, which fails to fully leverage the parallelism of the hardware array. Therefore, to eliminate this bottleneck and improve performance, we configured a dedicated parallel dispatch queue (MyParallelIOQueue) for the UserProcessParallelTask method. However, during our implementation attempt, we encountered a critical issue that caused a system-wide crash. The Operation Causing the Panic: We configured MyParallelIOQueue using the following combination of methods: In the .iig file: We appended the QUEUENAME(MyParallelIOQueue) macro after the override keyword of the UserProcessParallelTask method declaration. In the .cpp file: We manually created a queue with the same name by calling the IODispatchQueue::Create() function within our UserInitializeController method. The Result: This results in a macOS kernel panic during the DEXT loading process, forcing the user to perform a hard reboot. After the reboot, checking with the systemextensionsctl list command reveals the DEXT's status as [activated waiting for user], which indicates that it encountered an unrecoverable, fatal error during its initialization. Key Code Snippets to Reproduce the Panic: In .iig file - this was our exact implementation: class DRV_MAIN_CLASS_NAME: public IOUserSCSIParallelInterfaceController { public: virtual kern_return_t UserProcessParallelTask(...) override QUEUENAME(MyParallelIOQueue); }; In .h file: struct DRV_MAIN_CLASS_NAME_IVars { // ... IODispatchQueue* MyParallelIOQueue; }; In UserInitializeController implementation: kern_return_t IMPL(DRV_MAIN_CLASS_NAME, UserInitializeController) { // ... // We also included code to manually create the queue. kern_return_t ret = IODispatchQueue::Create("MyParallelIOQueue", kIODispatchQueueReentrant, 0, &ivars->MyParallelIOQueue); if (ret != kIOReturnSuccess) { // ... error handling ... } // ... return kIOReturnSuccess; } Our Question: What is the officially recommended and most stable method for configuring UserProcessParallelTask_Impl() to use a parallel I/O queue? Clarifying this is crucial for all developers pursuing high-performance storage solutions with DriverKit. Any explanation or guidance would be greatly appreciated. Best Regards, Charles
28
0
5.4k
Jun ’26
USB HID Digitizer support on macOS
I'm investigating supporting a touchscreen digitizer on macOS. I'd like to receive multi-touch reports from the device, and have them intercepted by my app. I also want to suppress the default absolute positioning 'mouse' behavior of the touch screen. The device exposes three HID interface: #0 - multi-touch (PrimaryUsagePage 0xD, PrimaryUsage 4) #1 - vendor-specific #2 - single-touch (PrimaryUsagePage 1, PrimaryUsage 2) I've only been able to achieve half of my goal using a HIDDriverKit dext - I can outmatch the OS for the single-touch HID interface and ignore its 7-byte single-touch reports. However, although I can match to the multi-touch interface, I never see any reports at all there, as if the OS never polls the interrupt endpoint. On Windows, the device "just works" - I've traced its behavior in Wireshark. The OS doesn't do any special setup, it sends no SET_FEATURE commands, it just reads from the multi-touch interrupt endpoint, where it receives 54-byte reports. Windows doesn't even get any 7-byte single-touch reports. On macOS, I managed to use Wireshark on an old Intel Mac, where I can still use XHC20 for logging. Here, macOS tries to read from all the interrupt endpoints for all the HID interfaces, and the digitizer only responds on the single-touch interface. MSDN's documentation for multi-touch support is quite unhelpful here, because it just says "use the OS driver", but doesn't detail how a digitizer switches between multi-touch and single-touch mode. If I were making a digitizer, I'd send reports on both interfaces, expecting the OS to read the single- or multi-touch interface as required. Although unlikely, it seems that this digitizer changes its behavior based on how it is accessed. I can outmatch the USB interface for the single-touch reports, so that the OS HID driver doesn't even see it. That doesn't change the device behavior. The HIDDriverKit APIs I use imply setting up an interrupt read. I call Open on the interface, and implement a ReportAvailable callback. This works for the single-touch interface, but I get no reports on the multi-touch interface. All the calls with return values return kIOReturnSuccess. Does anyone know how multi-touch digitizers switch between single- and multi-touch mode (if indeed they have a mode at all), or why macOS apparently doesn't even read the multi-touch interrupt end point? Does anyone know how I can ensure that my HID driver actually reads the interrupt endpoint on the HID interface it is matched to? Does macOS deliberately prevent access to multi-touch HID interfaces?
2
0
1.4k
Jun ’26
[DEXT Migration Issue] IOUserSCSIParallelInterfaceController fails to handle low-level I/O from `diskutil`
Hello everyone, We are migrating our KEXT for a Thunderbolt storage device to a DEXT based on IOUserSCSIParallelInterfaceController. We've run into a fundamental issue where the driver's behavior splits based on the I/O source: high-level I/O from the file system (e.g., Finder, cp) is mostly functional (with a minor ls -al sorting issue for Traditional Chinese filenames), while low-level I/O directly to the block device (e.g., diskutil) fails or acts unreliably. Basic read/write with dd appears to be mostly functional. We suspect that our DEXT is failing to correctly register its full device "personality" with the I/O Kit framework, unlike its KEXT counterpart. As a result, low-level I/O requests with special attributes (like cache synchronization) sent by diskutil are not being handled correctly by the IOUserSCSIParallelInterfaceController framework of our DEXT. Actions Performed & Relevant Logs 1. Discrepancy: diskutil info Shows Different Device Identities for DEXT vs. KEXT For the exact same hardware, the KEXT and DEXT are identified by the system as two different protocols. KEXT Environment: Device Identifier: disk5 Protocol: Fibre Channel Interface ... Disk Size: 66.0 TB Device Block Size: 512 Bytes DEXT Environment: Device Identifier: disk5 Protocol: SCSI SCSI Domain ID: 2 SCSI Target ID: 0 ... Disk Size: 66.0 TB Device Block Size: 512 Bytes 2. Divergent I/O Behavior: Partial Success with Finder/cp vs. Failure with diskutil High-Level I/O (Partially Successful): In the DEXT environment, if we operate on an existing volume (e.g., /Volumes/MyVolume), file copy operations using Finder or cp succeed. Furthermore, the logs we've placed in our single I/O entry point, UserProcessParallelTask_Impl, are triggered. Side Effect: However, running ls -al on such a volume shows an incorrect sorting order for files with Traditional Chinese names (they appear before . and ..). Low-Level I/O (Contradictory Behavior): In the DEXT environment, when we operate directly on the raw block device (/dev/disk5): diskutil partitionDisk ... -> Fails 100% of the time with the error: Error: -69825: Wiping volume data to prevent future accidental probing failed. dd command -> Basic read/write operations appear to work correctly (a write can be immediately followed by a read within the same DEXT session, and the data is correct). 3. Evidence of Cache Synchronization Failure (Non-deterministic Behavior) The success of the dd command is not deterministic. Cross-environment tests prove that its write operations are unreliable: First Test: In the DEXT environment, write a file with random data to /dev/disk5 using dd. Reboot into the KEXT environment. Read the data back from /dev/disk5 using dd. The result is a file filled with all zeros. Conclusion: The write operation only went to the hardware cache, and the data was lost upon reboot. Second Test: In the DEXT environment, write the same random file to /dev/disk5 using dd. Key Variable: Immediately after, still within the DEXT environment, read the data back once for verification. The content is correct! Reboot into the KEXT environment. Read the data back from /dev/disk5. This time, the content is correct! Conclusion: The additional read operation in the second test unintentionally triggered a hardware cache flush. This proves that the dd (in our DEXT) write operation by itself does not guarantee synchronization, making its behavior unreliable. Our Problem Based on the observations above, we have the conclusion: High-Level Path (triggered by Finder/cp): When an I/O request originates from the high-level file system, the framework seems to enter a fully-featured mode. In this mode, all SCSI commands, including READ/WRITE, INQUIRY, and SYNCHRONIZE CACHE, are correctly packaged and dispatched to our UserProcessParallelTask_Impl entry point. Therefore, Finder operations are mostly functional. Low-Level Path (triggered by dd/diskutil): When an I/O request originates from the low-level raw block device layer: The most basic READ/WRITE commands can be dispatched (which is why dd appears to work). However, critical management commands, such as INQUIRY and SYNCHRONIZE CACHE, are not being correctly dispatched or handled. This leads to the incorrect device identification in diskutil info and the failure of diskutil partitionDisk due to its inability to confirm cache synchronization. We would greatly appreciate any guidance, suggestions, or insights on how to resolve this discrepancy. Specifically, what is the recommended approach within DriverKit to ensure that a DEXT based on IOUserSCSIParallelInterfaceController can properly declare its capabilities and handle both high-level and low-level I/O requests uniformly? Thank you. Charles
Replies
12
Boosts
0
Views
2.5k
Activity
Jul ’26
Automate system extensions installation
Hello, We are running some tests with our driver with SIP on. We have all the entitlements and everything works smoothly. Thing is, when we run our xxxx.app from Applications, it pops up a GUI with install and uninstall button that we created. When we do install, it prompts us to enable system extension in System settings. I am wondering if there is a way to automate this. I understand I can automate running the xxxx.app from command line but can we automate having to go to System settings->login items & Extensions and enabling our system extension from command line too. Does Apple force an user to go to settings and do it once for security? From my research, I did not find any reliable answer to this. Thank you for your help!
Replies
1
Boosts
0
Views
1.6k
Activity
Jul ’26
DriverKit VLAN offload: IOUserNetworkPacket::getVlanTag() always returns false, kFeatureHardwareVlan undocumented
I've built an open-source DriverKit + NetworkingDriverKit (IOUserNetworkEthernet/Skywalk) driver for a USB 5GbE adapter (AQTION AQC111U chipset). As far as I can tell this is the first public one for real third-party hardware: github.com/jquirke/AQC111Driver It's a fully functional driver at this point: RX/TX hardware checksum offload, jumbo frame/MTU control up to 16KB, runtime-controllable diagnostics via a custom IOUserClient, and most recently working 802.1Q VLAN support via macOS's vlan(4) software path. While attempting to implement hardware offload VLAN support, I ran into what looks like a gap between documentation and the public SDK, and I'd appreciate expert opinion either way before filing Feedback. The issue: IOUserNetworkPacket::getVlanTag()/setVlanTag() (DriverKit 24.0+) have a doc comment stating: "Get the Vlan Tag from the packet, where the driver has enabled the kFeatureHardwareVlan capability; for the case that feature is not enabled, this method will return false." kFeatureHardwareVlan does not appear anywhere in the public NetworkingDriverKit.framework/Headers/ tree confirmed via exhaustive grep, including the full hwAssist/feature-flag enum in IOUserNetworkTypes.h. I tested every plausible related mechanism exhaustively, with a real device reattach for each combination, to rule out attach-time-only behaviour: +------------------------+--------------------------+--------------+-----------+ | HWAssist bit declared? | SetSoftwareVlanSupport()| getVlanTag() | vlan0 MTU | +------------------------+--------------------------+--------------+-----------+ | Yes | true | always false | 1500 | | Yes | false | always false | 1500 | | No | not called | always false | 1496 | | No | false | always false | 1496 | +------------------------+--------------------------+--------------+-----------+ none of these combinations gates real 802.1q tag-delivery/demux behavior at all; it seems Vlan support is completely implemented in software on the MacOS side and I have to explicitly program my hardware registers to disable VLAN tagging. Question: is hardware VLAN tag insert/strip (via getVlanTag()/setVlanTag()) currently reachable from a third-party DriverKit USB Ethernet driver at all? If kFeatureHardwareVlan is real but intentionally withheld from public headers, is there a documented path (entitlement, different NDK version, etc.) to enable it or is this confirmed unreachable without Apple's direct involvement (Feedback/DTS)? Can share full test logs/methodology if useful.
Replies
2
Boosts
2
Views
1.7k
Activity
Jul ’26
Entitlements received only for vendor ID. Is this normal?
Hi, I recently requested for some entitlements from Apple. In the form that I filled, there was only placeholder for Vendor ID so I put my vendor ID (in decimals). There was no placeholder to specify Device ID. However, in the Description placeholder at the end of the form, I did put the device ID (in decimals). After I got the entitlements, I tried loading my driver to match the device. It does match with only vendor ID but does not match with Vendor and Device ID together. So, now matching has widened little bit more than what we wanted. I was wondering if this is normal or if I did something wrong due to which entitlements was only granted for vendor ID but not for vendor + device Id. Thank you for your time!
Replies
1
Boosts
0
Views
1.7k
Activity
Jul ’26
[iOS 26] thermalmonitord cpu-avg-limiter-input-w2r read failure + SPMI bus faults on iPhone 15 Pro (A17 Pro) — likely driver regression
Since upgrading to iOS 26, my iPhone 15 Pro (A17 Pro) exhibits persistent battery drain and thermal issues. Console.app analysis via Mac reveals a cluster of related kernel and daemon errors that appear to stem from a driver-level regression rather than a hardware fault. Observed errors (continuous, since boot): thermalmonitord fails to read the cpu-avg-limiter-input-w2r property every 5 seconds indefinitely. This leaves the thermal throttling subsystem unable to regulate CPU load using its primary input sensor. The kernel logs SPMI bus faults on nub-spmi1 at a perfectly regular 30-second interval (codes 0x72040C01, 0x75E40C3B, 0x72D80C33), alongside aop-spmi0 faults (0x7A000830). The strict periodicity strongly suggests a driver retry loop rather than a dead hardware component. appleh16camerad (ISP driver) fails to initialize endpoint 1 (fISPEndpoints[1] is not ready) and retries every ~4 seconds, while the ANE driver (ANE0) cannot register its memory unwire timer. Both run in permanent retry loops consuming CPU cycles. AppleSMCFamily logs kSMCKeyNotWritable errors on SMC write attempts — the key exists but is flagged non-writable, suggesting incomplete driver initialization rather than a missing component. A single AppleSARService coredump request for the baseband was also observed. Why this appears to be a driver issue and not hardware: The system remains stable with no kernel panics or forced reboots. The SPMI faults occur on a precise 30-second schedule consistent with a kernel timer, not random hardware failures. The SMC error is kSMCKeyNotWritable (key present, wrong state) rather than kSMCKeyNotFound. All symptoms appeared immediately after the iOS 26 update with no physical event on the device. Device: iPhone 15 Pro — A17 Pro iOS version: 26.0 Reproduced: persistent across reboots, not tied to any specific app or usage pattern Has anyone observed the same pattern on A17 Pro devices? And has Apple acknowledged any SPMI / thermalmonitord regression in iOS 26 for this chip family?
Replies
3
Boosts
1
Views
1.6k
Activity
Jul ’26
DriverKit kernel crash, possible PCI bridge issue?
DriverKit kernel crash, possible PCI bridge issue? In working on a DriverKit driver for a legacy SCSI controller, we have finally arrived at the expected (and usually joyful) point in driver development - a repeatable kernel crash and reboot. It happens when the controller first attempts to do "real work" by accessing requests or replies provided to it by the driver. I will provide additional information below (and can share more), but it’s a bit tricky because there is a lot of steps required to get to the point where the PCIe card is sufficiently initialized to respond, presumably attempt a memory access, and bring down the whole system. The system freezes and reboots write after the first MemoryWrite32 with an address of a request. The address is properly (we believe) mapped, using IODMACommand et al, approximately like so: uint64_t reqArrSize = MPT_REQUEST_AREA * kMaxTasks; IOAddressSegment arrseg = {}; IOMemoryMap * arrmap = nullptr; ret = IOBufferMemoryDescriptor::Create(kIOMemoryDirectionInOut, reqArrSize, 0, &ivars->fReqArrayDesc); if (ret != kIOReturnSuccess) { … } IODMACommandSpecification dmaspec = {}; dmaspec.options = kIODMACommandSpecificationNoOptions; dmaspec.maxAddressBits = 32; // tried 31 here but that fails to allocate, the addresses start at 80000000, then leads to a crash // but that seems to be a bridge / SID issue, not the address itself ret = IODMACommand::Create(ivars->pciDevice, kIODMACommandCreateNoOptions, &dmaspec, &ivars->fReqArrayDMA); if (ret != kIOReturnSuccess) { … } ivars->fReqArrayDMA->retain(); uint64_t dmaFlags = 0; uint32_t segCount = 1; // capacity in; actual out IOAddressSegment segs[1] = {}; ret = ivars->fReqArrayDMA->PrepareForDMA(kIODMACommandPrepareForDMANoOptions, ivars->fReqArrayDesc, 0, reqArrSize, &dmaFlags, &segCount, segs); if ((ret != kIOReturnSuccess ) || (segCount != 1)) {…} ivars->fReqArrayPhys = segs[0].address; ivars->fReqArrayDesc->CreateMapping(0,0,0,0,0, &arrmap); // virtual mapping ivars->fReqArray = (uint8_t *)(arrmap ? arrmap->GetAddress() : 0); // virtual ivars->fReqFreemap.set(); // mark all request entries as free memset(ivars->fReqArray, 0, reqArrSize); The crash is very violent and consistent: panic(...): "dart-apciec0 (...): DART DART exception SID 0 ERROR_STATUS 0x80000001 ERROR_ADDRESS 0x0000000080000000 (no exceptionInfo)" @AppleT8110DART.cpp:1720 The fault address is the address we write to one of the controller's control register. We suspect that the issue is that this card uses an 8114 bridge, which uses its SID for the request, instead of the (scsi controller chip) endpoint. The mapping, meanwhile, is under the endpoint’s SID. So when the controller attempts its first request using the physical address, the mapping does not exist at the right level - which brings down the whole system. pcic0-bridge 0x106b/0x1015 Apple TB PCIe port └ pci-bridge 0x1b21/0x2461 ASMedia (TB tunnel) └ pci-bridge 0x1b21/0x2461 ASMedia IOPCITunnelled=Yes └ pci-bridge 0x10b5/0x8114 - (on the controller card) PLX PEX 8114, PCIe-to-PCI-X bridge └ scsi@8 0x1000/0x0030 - (on the controller card), LSI, on bus 4 (PCI-X secondary side) Worse yet, there appears to be no way form within a DEXT to ask for a mapping at a different level, and the 8114 doesn’t have a mapper of its own anyway (attempting to do so with a separate DEXT fails). That last part we know because we tried a workaround with two DEXTs, one that successfully matches the 8114 bridge and the other that matches the SCSI controller chip itself. However, the bridge doesn’t have a mapper attached and so the OS does not seem to give us a useful address (using the same IOBufferMemoryDescriptor::Create, ODMACommand::Create, PrepareForDMA sequence), and 32 bit request simply fails with kIOReturnMessageTooLarge. Attached is a quick diagram of our suspicions and a longer write-up (far warning, unlike the above, that is mostly AI output but it’s been reviewed by the team). Questions: Have others dealt with this problem of legacy PCI devices that have bridges that don’t fit neatly into the restrictions, and what did you do? Is there a way to get the right virtual<->physical mappings recognized at the right level? Is there a way to temporarily turn off SID checking or is that (as I assume) intrinsic to how this works? Are we on the wrong track entirely?
Replies
1
Boosts
0
Views
1.6k
Activity
Jul ’26
Reboot-free upgrade of an always-matched DriverKit dext
I have a DriverKit dext that implements a virtual SCSI HBA (no physical hardware). Because a bare IOUserSCSIParallelInterfaceController has no provider to match, the bundle ships two IOKitPersonalities: Bootstrap — IOClass IOUserService, IOProviderClass IOUserResources, IOResourceMatch IOKit. In Start() it does SetProperties({NvmeOfSCSIHBA: true}) + RegisterService(), publishing itself as a nub. Controller — IOClass IOUserSCSIParallelInterfaceController, IOProviderClass IOUserService, IOPropertyMatch {NvmeOfSCSIHBA: true} — it matches the bootstrap nub. This loads and runs correctly. The problem is upgrades. Activating a higher CFBundleVersion via OSSystemExtensionRequest.activationRequest (in-place replace) always defers the old version's termination to reboot. The new version reaches [activated enabled] but never starts; the old process keeps running until reboot. From sysextd/kernelmanagerd: kernelmanagerd Dext … v15 … is being replaced and cannot be terminated right away sysextd delegate returns Error Domain=OSSystemExtensionErrorDomain Code=101 "…is being replaced", assumes responsibility for old version …, keeping old version 15 sysextd turning the responsibility for termination of …, version 15 over to delegate (with uninstallation at the next reboot) sysextd a category delegate declined to terminate extension with identifier: … sysextd v15 terminating_for_uninstall → terminating_for_upgrade_via_delegate Key observation: this defers even on a fresh boot where the dext was never opened — no app/daemon ever opened the IOUserClient, no I/O, nothing attached beyond the controller↔nub match. So it does not appear to be a "client still holds it open" / busy-state situation; the driver_extension category delegate declines the moment it's a replacement. What I've tried: In-place activationRequest (replace): always defers to reboot (above). deactivationRequest (standalone): the request hangs — no delegate callback at all (waited ~13 min), even with no client open. Disconnecting all clients first (graceful Stop() that cancels its dispatch queues and completes async) does not change the replace deferral. My understanding from the docs/forums is that the normal reboot-free replace relies on the backing device being disconnected/reconnected to quiesce the old dext (thread 677040). My controller matches a persistent IOUserResources-backed nub that never detaches, so there's no equivalent quiesce point. Questions: For a dext whose only provider is a self-published IOUserResources nub (no detachable hardware), is reboot-free replacement structurally impossible — i.e. is the Code=101 "is being replaced" defer inherent to this matching pattern? Is the supported way to live-upgrade such a dext to deactivationRequest → (on .completed) → activationRequest rather than an in-place replace? If so, what makes a deactivationRequest complete in-session vs. defer to reboot for an IOUserResources-matched dext — and what would cause it to hang with no delegate callback? (Daemon's IOUserClient is closed; the controller's Stop() cancels its queues and completes.) Should the dext itself proactively tear down the published nub (e.g. terminate the bootstrap IOService) before/at upgrade so the controller detaches — or does that just re-match the still-staged old personalities and relaunch the old version? Is there a recommended pattern for a virtual (hardwareless) DriverKit HBA that needs in-field, reboot-free version updates, or is reboot genuinely required for this class of dext? Environment: macOS 27 (Tahoe)
Replies
1
Boosts
0
Views
1.4k
Activity
Jul ’26
Latency critical DMA read via PCIe
Dear All, I am currently developing a high throughput audio system which operates via PCIe tunneled into a USB4 interface. This include a custom FPGA based hardware and custom Audio DriverKit driver. While performing read operation via the hw DMA (that is a Host to Device transfer), I am noticing sparse latency spikes into the read transfers. Specifically, 4KB operations (which I assume including MRd + CpID) take normally from 5us to 40us to be completed, perfectly fine for my case. However, in some rare occasions, they can end up to 400us, which causes me overruns. The measurements have been carried out from the FPGA and they include the overall request and transfer time. While trying to tackle the problem, I'm investigating the possible power saving options and performance constraint methods at my disposal. I currently use these methods to mitigate the problem. ChangePowerState(kIOServicePowerCapabilityOn); SetPowerOverride(true); RequireMaxBusStall(kIOMaxBusStall25usec); CreatePMAssertion(kIOServicePMAssertionCPUBit | kIOServicePMAssertionForceFullWakeupBit, &ivars->PMAssertionID, false); The buffers are currently about 16MB, single segment, 16KB aligned and, of course, "prepared" for DMA. The system run for 3 hours without any overrun, but I'm not still fully convinced about its reliability. May someone provide me some comments on this? Are there profiling tools that I can use? Feel free to request me any required detail. The testing system is a MacBook Pro M2 Pro. Many Thanks and Best Regards Francesco
Replies
9
Boosts
0
Views
1.6k
Activity
Jun ’26
Reboot-free upgrade of an always-matched DriverKit dext
I have a DriverKit dext that implements a virtual SCSI HBA (no physical hardware). Because a bare IOUserSCSIParallelInterfaceController has no provider to match, the bundle ships two IOKitPersonalities: Bootstrap — IOClass IOUserService, IOProviderClass IOUserResources, IOResourceMatch IOKit. In Start() it does SetProperties({NvmeOfSCSIHBA: true}) + RegisterService(), publishing itself as a nub. Controller — IOClass IOUserSCSIParallelInterfaceController, IOProviderClass IOUserService, IOPropertyMatch {NvmeOfSCSIHBA: true} — it matches the bootstrap nub. This loads and runs correctly. The problem is upgrades. Activating a higher CFBundleVersion via OSSystemExtensionRequest.activationRequest (in-place replace) always defers the old version's termination to reboot. The new version reaches [activated enabled] but never starts; the old process keeps running until reboot. From sysextd/kernelmanagerd: kernelmanagerd Dext … v15 … is being replaced and cannot be terminated right away sysextd delegate returns Error Domain=OSSystemExtensionErrorDomain Code=101 "…is being replaced", assumes responsibility for old version …, keeping old version 15 sysextd turning the responsibility for termination of …, version 15 over to delegate (with uninstallation at the next reboot) sysextd a category delegate declined to terminate extension with identifier: … sysextd v15 terminating_for_uninstall → terminating_for_upgrade_via_delegate Key observation: this defers even on a fresh boot where the dext was never opened — no app/daemon ever opened the IOUserClient, no I/O, nothing attached beyond the controller↔nub match. So it does not appear to be a "client still holds it open" / busy-state situation; the driver_extension category delegate declines the moment it's a replacement. What I've tried: In-place activationRequest (replace): always defers to reboot (above). deactivationRequest (standalone): the request hangs — no delegate callback at all (waited ~13 min), even with no client open. Disconnecting all clients first (graceful Stop() that cancels its dispatch queues and completes async) does not change the replace deferral. My understanding from the docs/forums is that the normal reboot-free replace relies on the backing device being disconnected/reconnected to quiesce the old dext (thread 677040). My controller matches a persistent IOUserResources-backed nub that never detaches, so there's no equivalent quiesce point. Questions: For a dext whose only provider is a self-published IOUserResources nub (no detachable hardware), is reboot-free replacement structurally impossible — i.e. is the Code=101 "is being replaced" defer inherent to this matching pattern? Is the supported way to live-upgrade such a dext to deactivationRequest → (on .completed) → activationRequest rather than an in-place replace? If so, what makes a deactivationRequest complete in-session vs. defer to reboot for an IOUserResources-matched dext — and what would cause it to hang with no delegate callback? (Daemon's IOUserClient is closed; the controller's Stop() cancels its queues and completes.) Should the dext itself proactively tear down the published nub (e.g. terminate the bootstrap IOService) before/at upgrade so the controller detaches — or does that just re-match the still-staged old personalities and relaunch the old version? Is there a recommended pattern for a virtual (hardwareless) DriverKit HBA that needs in-field, reboot-free version updates, or is reboot genuinely required for this class of dext? Environment: macOS 27 (Tahoe)
Replies
0
Boosts
0
Views
1.1k
Activity
Jun ’26
Supported way to expose an iPhone+controller as a macOS gamepad without restricted entitlements?
I’m prototyping a personal-use system that lets an iPhone with a physically attached controller act as an input device for a Mac. End goal: Use the iPhone as the transport and sensor host Use the attached physical controller for buttons/sticks Map the iPhone gyroscope to the controller’s right stick to get gyro aim in Mac games / cloud-streamed games such as GeForce NOW that don't support the gyro. What I’m trying to understand is whether Apple supports any path for this on macOS that does NOT require restricted entitlements or paid-program-only capabilities. What I’ve already found: CoreHID virtual HID device creation appears to require com.apple.developer.hid.virtual.device HIDDriverKit / system extensions appear to require Apple-granted entitlements as well GCVirtualController does not seem to solve the problem because I need a controller-visible device that other apps can see, not just controls inside my own app So my concrete question is: Is there any supported, entitlement-free way for a personal macOS app to expose a game-controller-like input device that other apps can consume system-wide? If not, is the official answer that this class of solution necessarily requires one of: CoreHID with restricted entitlement HIDDriverKit/system extension entitlement some other Apple-approved framework or program I’m missing I’m not asking about App Store distribution. This is primarily for local/personal use during development. I’m trying to understand the supported platform boundary before investing further. Any guidance on the recommended architecture for this use case would be appreciated.
Replies
4
Boosts
1
Views
2.3k
Activity
Jun ’26
HAL Plugin (AudioServerPlugin) — Plugin_StartIO never called from AUHAL input client
I'm building a virtual audio device using the HAL Plugin (AudioServerPlugin) API on macOS. The plugin loads correctly, WriteMix is called with non-zero audio data, but Plugin_StartIO is never called from my app's AUHAL input client. Environment: macOS 26.5 Xcode (latest) Bundle ID: com.private.SubON Plugin installed at: /Library/Audio/Plug-Ins/HAL/SubONHALPlugin.driver What works: Plugin loads and is visible as "SubON Virtual Device" Plugin_AddDeviceClient is called with bundleID=com.private.SubON WriteMix is called with non-zero maxSrc values (audio is reaching the plugin) AUHAL setup completes: EnableIO input=1 output=0, CurrentDevice set correctly, AudioUnitInitialize succeeds pre-start readback confirms: currentDevice matches, enableIOIn=1 What doesn't work: Plugin_StartIO is never called from the SubON.app input client WillDoIOOperation is never called ReadInput is never called maxAmplitude in the input tap is always 0.0 AUHAL setup code (Swift): AudioUnitUninitialize(auhal) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_EnableIO, kAudioUnitScope_Input, 1, &one, size) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_EnableIO, kAudioUnitScope_Output, 0, &zero, size) AudioUnitSetProperty(auhal, kAudioOutputUnitProperty_CurrentDevice, kAudioUnitScope_Global, 0, &deviceID, size) AudioUnitInitialize(auhal) HAL Plugin — WillDoIOOperation: outWillDo = true; outWillDoInPlace = true; Returns true for both ReadInput and WriteMix. Observation: Even when selecting "SubON Virtual Device" as the system input device in System Settings, Plugin_StartIO is still never called. Any ideas what could prevent Plugin_StartIO from being called despite AUHAL configuration appearing correct?
Replies
0
Boosts
0
Views
1.6k
Activity
Jun ’26
Simple question on
Hopefully a very quick question for anyone familiar with IOUserSCSIParallelInterfaceController - what is the right initialization to implement: init () override; Start (IOService * provider) override; UserInitializeController () override; something else Seems #3 is required, but guidance varies on the others, undoubtedly bc IOUserSCSI.. implements a lot of things beyond the usual DriverKit structure. Thanks in advance for any help. (We're trying to implement a driver for a legacy SCSI controller).
Replies
3
Boosts
0
Views
1.2k
Activity
Jun ’26
iPad USB-C (serial communication) by cable
Hello, I have a device like a gas meter or an electricity meter and it has: an optical interface IEC 62056-21 (IEC-1107) with support for speeds up to 115,200 Bd. On Windows and Android, we use a cable that has an optical interface and on the other end we connect USB A to the PC and to the Android via an OTG to USB adapter. The cable contains a chip from FTDI FT230XQ. I have an application in MAUI where I want to connect this cable to the 10th generation iPad and communicate similarly to, for example, via the COM5 port on the PC. When the port opens, I send a query and get a response. Is it possible, what should I do for this? What about Apple certification of cables? Is it possible to send a packet from MAUI via the USB C port via the cable and then receive and process the packet again? What about MFi? I found this: https://redpark.com/usb-c-serial-cable/ Please can you give me some idea or expert to this topic? Thanks, Roman
Replies
1
Boosts
0
Views
1.1k
Activity
Jun ’26
Our driver next fails due to DriverKit attempting to call
We are developing an IOUserSCSIParallelInterfaceController driver for a legacy controller. After completing init() successfully, no other methods are called before a DriverKit assert failure - .driver.dext) Assertion failed: (notsync || !remote || (msgid == IOService_Start_ID) || queue->OnQueue()), function Invoke, file uioserver.cpp, line 1654. - that leads immediately to "IOPCIDevice::ClientCrashed_Impl() for client " . This appears to be because the framework is attempting a SetPowerState()' during DEXT load, which is delivered off-queue and panics in OSMetaClassBase::Invoke (uioserver.cpp`) before any other dext method runs. Apple Silicon Mac, macOS 26 (DriverKit 25.1 SDK), Xcode 26.x. Expected: The SetPowerState() power-up is delivered on the driver object's dispatch queue (or otherwise handled by the framework), allowing the dext's SetPowerState override to run, ACK via super::SetPowerState(powerFlags, SUPERDISPATCH), and proceed to UserInitializeController. Actual behavior: init() completes (our trace logs init then completed init) Neither Start_Impl nor SetPowerState_Impl ever executes Instead the process fails with the assertion above , IOPCIDevice::ClientCrashed_Impl() reports "client … does not have open session … skipping recovery". The dext crash-loops ("Driver … has crashed N time(s)"). Any suggestions?
Replies
5
Boosts
0
Views
1.4k
Activity
Jun ’26
How to deliver a USBDriverKit driver in an SDK or Framework for sale to third parties?
I have a product that currently communicates to a piece of proprietary Medical hardware via USB. We have a driver created with USBDriverKit that is a hard requirement for this product to function. Currently, we are delivering an iPadOS application that utilizes the driver. Our next step is to create an SDK that includes all of the Frameworks and the driver utilized by the application. Since the driver is a system extension that lives in the application, how do we bundle it with our SDK and make it available for use by third-parties?
Replies
5
Boosts
0
Views
1.8k
Activity
Jun ’26
System Panic with IOUserSCSIParallelInterfaceController during Dispatch Queue Configuration
Hello everyone, We are in the process of migrating a high-performance storage KEXT to DriverKit. During our initial validation phase, we noticed a performance gap between the DEXT and the KEXT, which prompted us to try and optimize our I/O handling process. Background and Motivation: Our test hardware is a RAID 0 array of two HDDs. According to AJA System Test, our legacy KEXT achieves a write speed of about 645 MB/s on this hardware, whereas the new DEXT reaches about 565 MB/s. We suspect the primary reason for this performance gap might be that the DEXT, by default, uses a serial work-loop to submit I/O commands, which fails to fully leverage the parallelism of the hardware array. Therefore, to eliminate this bottleneck and improve performance, we configured a dedicated parallel dispatch queue (MyParallelIOQueue) for the UserProcessParallelTask method. However, during our implementation attempt, we encountered a critical issue that caused a system-wide crash. The Operation Causing the Panic: We configured MyParallelIOQueue using the following combination of methods: In the .iig file: We appended the QUEUENAME(MyParallelIOQueue) macro after the override keyword of the UserProcessParallelTask method declaration. In the .cpp file: We manually created a queue with the same name by calling the IODispatchQueue::Create() function within our UserInitializeController method. The Result: This results in a macOS kernel panic during the DEXT loading process, forcing the user to perform a hard reboot. After the reboot, checking with the systemextensionsctl list command reveals the DEXT's status as [activated waiting for user], which indicates that it encountered an unrecoverable, fatal error during its initialization. Key Code Snippets to Reproduce the Panic: In .iig file - this was our exact implementation: class DRV_MAIN_CLASS_NAME: public IOUserSCSIParallelInterfaceController { public: virtual kern_return_t UserProcessParallelTask(...) override QUEUENAME(MyParallelIOQueue); }; In .h file: struct DRV_MAIN_CLASS_NAME_IVars { // ... IODispatchQueue* MyParallelIOQueue; }; In UserInitializeController implementation: kern_return_t IMPL(DRV_MAIN_CLASS_NAME, UserInitializeController) { // ... // We also included code to manually create the queue. kern_return_t ret = IODispatchQueue::Create("MyParallelIOQueue", kIODispatchQueueReentrant, 0, &ivars->MyParallelIOQueue); if (ret != kIOReturnSuccess) { // ... error handling ... } // ... return kIOReturnSuccess; } Our Question: What is the officially recommended and most stable method for configuring UserProcessParallelTask_Impl() to use a parallel I/O queue? Clarifying this is crucial for all developers pursuing high-performance storage solutions with DriverKit. Any explanation or guidance would be greatly appreciated. Best Regards, Charles
Replies
28
Boosts
0
Views
5.4k
Activity
Jun ’26
USB HID Digitizer support on macOS
I'm investigating supporting a touchscreen digitizer on macOS. I'd like to receive multi-touch reports from the device, and have them intercepted by my app. I also want to suppress the default absolute positioning 'mouse' behavior of the touch screen. The device exposes three HID interface: #0 - multi-touch (PrimaryUsagePage 0xD, PrimaryUsage 4) #1 - vendor-specific #2 - single-touch (PrimaryUsagePage 1, PrimaryUsage 2) I've only been able to achieve half of my goal using a HIDDriverKit dext - I can outmatch the OS for the single-touch HID interface and ignore its 7-byte single-touch reports. However, although I can match to the multi-touch interface, I never see any reports at all there, as if the OS never polls the interrupt endpoint. On Windows, the device "just works" - I've traced its behavior in Wireshark. The OS doesn't do any special setup, it sends no SET_FEATURE commands, it just reads from the multi-touch interrupt endpoint, where it receives 54-byte reports. Windows doesn't even get any 7-byte single-touch reports. On macOS, I managed to use Wireshark on an old Intel Mac, where I can still use XHC20 for logging. Here, macOS tries to read from all the interrupt endpoints for all the HID interfaces, and the digitizer only responds on the single-touch interface. MSDN's documentation for multi-touch support is quite unhelpful here, because it just says "use the OS driver", but doesn't detail how a digitizer switches between multi-touch and single-touch mode. If I were making a digitizer, I'd send reports on both interfaces, expecting the OS to read the single- or multi-touch interface as required. Although unlikely, it seems that this digitizer changes its behavior based on how it is accessed. I can outmatch the USB interface for the single-touch reports, so that the OS HID driver doesn't even see it. That doesn't change the device behavior. The HIDDriverKit APIs I use imply setting up an interrupt read. I call Open on the interface, and implement a ReportAvailable callback. This works for the single-touch interface, but I get no reports on the multi-touch interface. All the calls with return values return kIOReturnSuccess. Does anyone know how multi-touch digitizers switch between single- and multi-touch mode (if indeed they have a mode at all), or why macOS apparently doesn't even read the multi-touch interrupt end point? Does anyone know how I can ensure that my HID driver actually reads the interrupt endpoint on the HID interface it is matched to? Does macOS deliberately prevent access to multi-touch HID interfaces?
Replies
2
Boosts
0
Views
1.4k
Activity
Jun ’26