We are conducting iBeacon compliance testing for our device and would like to clarify two test items from the iBeacon test specification: Regarding Tx power stability verification over time and across different battery capacities: Could you please specify the required test duration and the exact test procedure? Specifically, how long should the Tx power be monitored to verify stability within the 2dB standard deviation requirement, and what battery capacity levels (e.g., 100%, 50%, 20%, low battery threshold) should be tested? Regarding device interoperability with iOS CoreLocation APIs for beacon-based region monitoring and ranging: Could you please provide guidance on the test methodology? Specifically, what test cases, expected behaviors, and pass/fail criteria should we follow to verify correct interoperability with region monitoring (didEnter/didExit) and ranging (didRangeBeacons) APIs? Any official test guidelines or reference documents would be greatly appreciated.

Hi everyone, We're working on a custom USB-C accessory based on an MCU (ARM Cortex-R8, running RT-Thread RTOS) with a Synopsys DWC3 USB Device controller. Our goal is to stream real-time sensor data (~10 Mbps) from the accessory to an iPhone via USB-C. We're planning to configure our MCU as a USB NCM device (following USB-IF NCM v1.0 spec), so the iPhone sees it as a standard Ethernet adapter. We would then run a lightweight TCP/IP stack (lwIP) on the MCU side and communicate with our iOS app via standard BSD Sockets / Network.framework over the virtual network — no gateway, just direct IP-to-IP communication within the local network that the NCM device presents. Questions: Feasibility confirmation: Based on our description, do you see any issues with this approach on iPhones including iPhone 16 and newer models? Our USB controller supports High-Speed (480 Mbps), so NCM throughput should not be a bottleneck. No-gateway concern: We don't plan to implement a DHCP server or gateway on the MCU. We'd use static IP configuration (or Link-Local addressing) for direct socket communication. Is there anything in iOS's network stack that would prevent this — for example, requiring a DHCP-assigned address or a default gateway before allowing socket traffic on the USB Ethernet interface? MFi and long-term viability: We understand this approach doesn't require MFi certification, since NCM is a standard USB-IF class and iOS has built-in Ethernet support. However, we want to make sure this doesn't go against the spirit of the MFi program or Apple's accessory policies. Is there any risk that Apple might restrict or block non-MFi NCM accessories in a future iOS update? We'd rather invest our effort in the right approach from the start. App Store review: Would an iOS app that communicates with our accessory exclusively via standard socket APIs (Network.framework / BSD Sockets) over the USB Ethernet interface face any App Store review issues — assuming it doesn't use any private APIs and doesn't declare MFi support? Any guidance would be greatly appreciated. We want to make sure we're building on a solid foundation.

Hello, My name is Jisoo Kim, and I am a product designer currently developing a tray and case accessory for the Apple Magic Keyboard and Magic Trackpad. I have reviewed the Apple Accessory Design Guidelines, however I was unable to find specific guidance covering accessories of this type. As a designer and an engineer who values complementing Apple's devices without interfering with their functionality, I want to ensure our development aligns with Apple's standards. Given the absence of specific guidelines for this product category, I have two questions: Would it be appropriate to reference guidelines from other similar Apple accessory categories as a basis for our design decisions? Are there any additional considerations or requirements we should be aware of when developing this type of accessory? Any guidance you could provide would be greatly appreciated.

When using AccessorySetupKit to remove accessories, a pop-up window appears when calling removeAccessory. However, the text in the pop-up window does not change according to my iPhone's language settings and remains only in English. Has anyone encountered this issue? Does Apple have any plans to address this compatibility issue?

I’m debugging a custom BLE HID device on iPhone. It is a composite HID mouse + keyboard dongle. Setup: Hardware: Seeed XIAO nRF52840 Firmware: Adafruit Bluefruit Arduino / BLEHidAdafruit BLE HID report map: stock Adafruit composite HID with keyboard, consumer, and mouse reports GAP/advertising appearance: HID_MOUSE iOS adopts the device as an AssistiveTouch pointer Mouse movement and clicks work correctly Keyboard symptom: Lowercase/unshifted characters type correctly. Shifted characters lose the Shift modifier during text input: - A -> a - T -> t - DoorDash -> doordash - ! -> 1 - @ -> 2 - # -> 3 - { -> [ - } -> ] Confirmed: The iOS app sends the exact intended string to the dongle. Firmware receives the exact string. Firmware computes and sends the expected HID modifier/keycode: A sends modifier 0x02 + HID_KEY_A ! sends modifier 0x02 + HID_KEY_1 A lone isolated "A" still lands as "a", so this does not appear to be a timing or repeated-key issue. Cmd+Space works from the same HID keyboard report path and opens Spotlight. Full Keyboard Access is off. Turning AssistiveTouch off does not fix it. The iPhone never shows "Hardware Keyboard" settings for this device, even when searching Settings. Question: Is there a documented distinction on iOS between accepting BLE HID keyboard reports for global shortcuts, such as Cmd+Space, and admitting the same device as a full Hardware Keyboard for text composition? In particular: Does the absence of Hardware Keyboard settings mean iOS has not classified the device as a real external keyboard? Can a composite BLE HID device advertised as HID_MOUSE be accepted for pointer input but have Shift ignored for text input? Does iOS require a different GAP appearance, HID report-map structure, report ordering, or separate keyboard identity for Shift/modifier text composition to work? Is there a recommended way to build a BLE HID device that preserves AssistiveTouch pointer behavior while also being treated as a full external keyboard?

Hello, I am developing a cross-platform mobile app that communicates with an external accessory over a serial (UART) link. HARDWARE : The accessory is an optical reading probe that connects to the phone via USB. Inside the cable there is a standard FTDI USB-to-serial chip (similar to common FTDI/CP210x USB-serial adapters). WHAT WORKS On Android, our app: Detects the USB device Opens the serial port Reads and writes raw bytes successfully This wired FTDI path is fully implemented and working. WHAT DOES NOT WORK On iPhone, using the same wired FTDI USB accessory: We connect via Lightning or USB-C adapter The app never sees the FTDI device We cannot find a public iOS API to open a generic USB-serial port MY QUESTION : Is there any supported way for a third-party iOS app to communicate with a generic FTDI USB-serial device over a wired USB connection? Specifically, am I missing: A public Apple framework for USB serial? An Info.plist key or entitlement? A system driver on iOS similar to macOS AppleUSBFTDI (TN2315)? Or is wired USB-serial on iPhone only possible with MFi-certified accessories (External Accessory framework) or another transport such as Bluetooth LE? WHAT I HAVE ALREADY CHECKED External Accessory: seems to require MFi hardware and a registered protocol string. Our FTDI probe is not MFi. TN2315 (AppleUSBFTDI): appears to be macOS only, not iOS. Physical USB connection: cable fits, but no serial API is exposed to the app. ENVIRONMENT Platform: iOS (iPhone) Language: C# / .NET-iOS Need: transparent byte-level serial read/write SUMMARY: Android USB-serial works with our FTDI wired accessory. iOS does not. Am I missing something on iOS, or is generic FTDI USB-serial simply not supported for third-party iPhone apps? Thank you for any guidance.

I recently updated my iPhone SE (2020) to the iOS 27 beta, and initially the experience was excellent. The phone felt noticeably faster and more responsive, and I was genuinely impressed with the update. However, after about a day of usage, I started experiencing a charging-related issue. One night, I left my phone connected to the charger before going to sleep when the battery was at 55%. The next morning, I found that the battery had dropped to 42% instead of charging. I checked all connections and confirmed that the charger, cable, and power source were properly connected. When I disconnected and reconnected the charger, the charging lightning bolt icon would briefly appear, then turn grey after about two seconds, and finally disappear completely a couple of seconds later. The phone would not charge. Assuming it might be a faulty charger or cable, I tested with: A different Apple charger A different Lightning cable The same issue persisted. Next, I connected the phone to my Mac. Surprisingly, it started charging, and Finder recognized the device normally. Over the next few days, the behavior became inconsistent: Sometimes the phone would charge. Sometimes it would not charge at all. Connecting to the Mac worked most of the time, but occasionally even that failed. I also noticed another unusual behavior: If I unplugged the Lightning cable from the iPhone and plugged it back in, the charging symbol would briefly appear. However, if I left the cable connected to the iPhone and unplugged/replugged only the USB end from the power adapter, there would be no response whatsoever—no charging sound, no charging icon, nothing. I cleaned the charging port, cable connectors, and charger contacts, but the issue remained. At that point, I realized the problem started immediately after installing the iOS 27 beta. To verify whether it was software-related, I restored the device back to iOS 26.5. After downgrading, the charging issue completely disappeared, and the phone began charging normally again with the same charger and cable. Based on my testing, this appears to be a software-related issue introduced in the iOS 27 beta rather than a hardware problem. I am posting this in case other iPhone SE (2020) users are experiencing similar charging behavior after updating to the beta. Device: iPhone SE (2020) Issue: Intermittent charging failure after updating to iOS 27 beta Status: Resolved after restoring to iOS 26.5

Is there any UIRequiredDeviceCapabilities string that can be used to restrict an app to Apple TV 4K (2nd generation) or later hardware? I can’t find one. I’m working on a tvOS app that uses Continuity Camera. That feature only works on Apple TV 4K (2nd gen) and Apple TV 4K (3rd gen) hardware. There seems be no way to warn App Store customers that the app will not work on Apple TV 4K (1st gen). In the App Store or TestFlight, a user with a 1st gen device incorrectly sees a compatibility note that the app “Works on this Apple TV”. Setting a minimum OS version is not currently a helpful path for me — even tvOS 26.5 is compatible with 1st generation hardware. I can’t think of a good way to prevent users with an incompatible Apple TV 4K from installing an app that won’t work on their 1st generation devices. Any ideas? Am I missing something?

On Apple Watch (reported several times, but also on a powerful Ultra3), the CMAltimeter occasionally stops delivering updates for a while (a couple of minutes) then resumes. This makes for a terrible user experience. What could cause this? Is there a way to (best case) prevent this, or (workaround) detect it? This is production critical, any help would be greatly appreciated. Thanks a lot!

So for last two years ive been dealing with unwanted unauthorized access to my data having zero clue what was the reasoning it. I need help to fix this please. I deal with random people "linking" up to my "whatever syncing or streamin" I never signed up for anything this and lost everything in my life over this. I finally found out the root (which is this program apple offers) and it's being used maliciously 100%. please help

I’m seeing a Bluetooth call audio routing issue on a new iPhone 17 Pro running iOS 26.5.1, build 23F81. Bluetooth media audio works normally. Music and video audio stay on Bluetooth headphones without issues. The problem appears only when the device switches into call audio / HFP mode. Tested with multiple earbuds: Samsung, OPPO, Huawei and CMF Buds Pro 2. The behavior is similar with all of them. There are no other Bluetooth devices connected. Call Audio Routing is already set to Bluetooth Headset in Accessibility settings. The issue affects cellular calls, FaceTime Audio, Telegram and Signal. In some cases the earbuds seem to switch into call mode, but the call audio route falls back to the iPhone receiver or speaker instead of staying on the Bluetooth headset. After the call ends, Bluetooth media audio returns normally. I captured a sysdiagnose right after reproducing the issue. Relevant observations from the logs: Device: iPhone18,2 iOS: 26.5.1 Build: 23F81 Sysdiagnose time: 2026-06-03 11:22:03 +0300 In Bluetooth/CoreCapture/bluetooth_status.txt, Bluetooth was ON 3 paired devices were present 1 device was connected Connected device at the time: CMF Buds Pro 2 So the headset was not simply disconnected from the phone. In the powerlog, before the call the audio route was HeadphonesBT for media playback. Around the FaceTime Audio test, HeadsetBT / PhoneCall appeared, but then the route moved to ReceiverAndMicrophone / Speaker instead of staying on HeadsetBT. During a later cellular call, the active PhoneCall route was also ReceiverAndMicrophone rather than HeadsetBT. After the call ended, the route returned to HeadphonesBT for media playback. This looks like the Bluetooth connection remains alive, but call audio / HFP routing fails. The same sysdiagnose also contains CentauriFirmwareEvent entries under crashes_and_spins from the previous day. They show: subsystem = BT host-reason = firmware crash BTMAIN panic faulting_task = link_manager_thread LMAC_5G watchdog expired SCAN watchdog expired These firmware crash events do not happen at the exact same timestamp as the call test, so I’m not claiming that every call directly crashes Bluetooth firmware. But the sysdiagnose shows both incorrect Bluetooth call audio routing and separate BT firmware crash events. Has anyone seen similar behavior on iPhone 17 / iOS 26 with Bluetooth HFP call audio? Could this be a known iOS 26 / Apple N1 / Bluetooth firmware issue, or does it look more like a hardware defect of this particular device?

Filing this for engineering visibility and to ask whether the observed behavior matches expected M5 Pro DCP architecture. FB22701284 contains full sysdiagnose and supporting data. Hardware Configuration MacBook Pro 16-inch (Mac17,8) M5 Pro chip, 18-core CPU 64GB unified memory (highest M5 Pro memory tier) 1TB SSD macOS Tahoe 26.4.1 (build 25E253) AppleDCP-1041.100.97~429-t605xdcp.RELEASE Display Configuration Two identical LG UltraGear 27GM950B monitors: 27" Mini LED panels, native 5120x2880 DisplayPort 2.1 UHBR20 (80 Gbps capable) 165Hz native refresh, HDR-capable Connection topology (all third-party display software removed for clean test): Mac TB5 port 1 → Silkland DP80 USB-C cable (VESA-certified) → Monitor #1 USB-C input Mac TB5 port 2 → Silkland DP80 USB-C cable (VESA-certified) → Monitor #2 USB-C input DisplayLink Manager fully uninstalled No dock, no MST hub, no signal converters Apple Specification Context Per the MacBook Pro user guide, M5 Pro supports dual displays at 5K@120Hz (support.apple.com/guide/macbook-pro/apd8cdd74f57/mac), with the documented instruction to "connect the display with the highest resolution first." Observed Behavior Solo connection (either monitor) Either monitor in isolation: 5120x2880 @ 144Hz, Maximum Source Bandwidth 27,400 Mbps, 10-bit, HDR enabled. Dual connection (BetterDisplay 4.3.3 diagnostic) Monitor on dispext0@B0000000: 5120x2880 @ 144Hz, Maximum Source Bandwidth: 27,400 Mbps, HDR enabled Monitor on dispext1@90000000: Degraded from native 5K, Maximum Source Bandwidth: 13,700 Mbps, HDR disabled The 27,400/13,700 split is deterministic and follows connection order. Hardware substitution (cables, ports, monitor positions) confirmed the allocation follows position in connection order, not specific hardware. Each monitor achieves full 27,400 Mbps when solo. Per-pipe budget structure exposed in BetterDisplay 4.3.3 Recent BetterDisplay versions expose allocation limits in display reports: Allocation limits - horizontal: 3360, 3840 pixels HiDPI (6720, 7680 pixels LoDPI) Allocation limits - vertical: 2304 pixels HiDPI (4608 pixels LoDPI) This matches the per-sub-pipe budget structure documented in third-party M5 Max DCP firmware analysis, where M5 Max shows MaxSrcRectWidthForPipe = (6720, 7680, 7680, 7680). M5 Pro appears to expose only two values (6720, 7680). WindowServer assertion failure WindowServer crash on 2026-05-16 with assertion failure in the function calculating per-pipe maximum source rectangle widths: Thread 16 Crashed: com.apple.coreanimation.render-server CA::WindowServer::AppleDisplay::max_src_rect_width_by_pipes(unsigned char) const + 92 CA::WindowServer::AppleDisplay::max_src_rect_pixels() const + 60 CA::WindowServer::Server::get_display_info() + 1812 Exception: EXC_CRASH (SIGABRT), Abort trap 6. This is the same function third-party DCP firmware analysis identifies as governing the per-sub-pipe budget calculation. Reference to Existing Thread Apple CoreOS DTS Engineer Kevin Elliott in thread 814201 (https://developer.apple.com/forums/thread/814201) described M5 MacBook Pro display architecture: "Driving the display at 240Hz require both of the two display 'pipes' and the system ends up allocating both pipes to the first monitor it discovers. That prevents it from lighting up the second monitor, as there isn't currently any way for software to shift allocations of display pipes between machines." That thread addressed a single-display 4K@240Hz scenario where the second display failed to initialize. The underlying allocation mechanism (first-come-first-served pipe assignment, no dynamic reallocation) appears consistent with the dual-display configuration I'm observing, with the manifestation differing (both displays initialize but the second is bandwidth-constrained rather than absent). Specific Technical Questions Is the 27,400/13,700 Mbps asymmetric allocation observed on dual 5K configurations the expected manifestation of the two-pipe architecture described in thread 814201, or a distinct allocation policy specific to dual-display scenarios? The advertised dual 5K@120Hz capability requires approximately 28 Gbps per stream. The observed allocation appears insufficient to drive both displays at this specification simultaneously. Is there a configuration approach that allows both displays to receive adequate bandwidth allocation? Multiple sources document that M5 Max has more display engine output channels than M5 Pro. Is the architectural difference between M5 Pro and M5 Max sub-pipe count (per the BetterDisplay allocation limits and third-party firmware analysis) the underlying explanation for the differential dual-display capability? The WindowServer assertion failure in max_src_rect_width_by_pipes() — is this a known edge case for dual high-bandwidth display configurations on M5 Pro, or should this be filed as a separate issue from the bandwidth allocation behavior? Supporting Data Available BetterDisplay 4.3.3 diagnostic reports for both monitors WindowServer crash report (2026-05-16) ioreg output showing DCP unit assignments sysdiagnose attached to FB22701284 Happy to provide additional FB tickets with focused diagnostic captures if specific data would help engineering investigation.

Watch is no longer capturing biometric data. No sleep, HR, or SPO2, steps and activity after downloading 26.5 watchOS beta. Reset watch and was not able to resolve the issue.

We were using a BLE mouse with HID command in iOS device, mainly iPhone device and we can use the mouse pointer using the assistive touch . But when we updated the iOS version to iOS 26.4.2 , the mouse pointer become very slow and jumpy. So something changed in the latest version that hurt the BLE mouse pointer Please update your feedback or similar issues

Is there any information available on how developers can implement the "Firmware Update Readiness" and/or "Firmware Update Status" characteristics in HomeKit? Many consumer devices support this (showing an "update available" icon), however, there appears to be nothing in the documentation about this characteristic, and it is not listed as an option in the HomeKit Accessory Simulator. Thanks in advance!

Hi, I am trying to build a very simple iOS app in Xcode that starts an NFCNDEFReaderSession when I press a button. My goal right now is only to verify that the NFC reading process starts correctly on a real iPhone. I am not trying to publish the app on the App Store. When I try to start the session, I get this error in the console: -[NFCHardwareManager areFeaturesSupported:outError:]:435 XPC Error: Error Domain=NSCocoaErrorDomain Code=4099 "The connection to service named com.apple.nfcd.service.corenfc was invalidated: Connection init failed at lookup with error 159 - Sandbox restriction." UserInfo={NSDebugDescription=The connection to service named com.apple.nfcd.service.corenfc was invalidated: Connection init failed at lookup with error 159 - Sandbox restriction.} and then my app reports that NFC is not available on this device. Important details: I added Near Field Communication Tag Reading in Signing & Capabilities. I added the NFC privacy usage description in the target settings. I am using automatic signing. I am not using an Apple Developer Program paid account. I am using a Personal Team / free account. I should also mention that I am not experienced with Swift/iOS development, so I may be missing something basic in the setup. My question is: Is this expected when using a Personal Team / free account, or is there some configuration issue I should still check? I am happy to provide any additional information needed

The app crashes when using EAAccessoryManager.showBluetoothAccessoryPicker(withNameFilter:) to connect to a Bluetooth accessory in a multi-accessory scenario. The crash occurs immediately after selecting an accessory from the picker UI. Steps to Reproduce: Ensure a Bluetooth accessory (Accessory A) is already connected to the iPhone/iPad and is visible in Bluetooth settings. Launch the app. Initiate a connection flow that presents the Bluetooth accessory picker using EAAccessoryManager.showBluetoothAccessoryPicker(withNameFilter:). Ensure another compatible accessory (Accessory B) is available and visible in the picker. Select Accessory B from the picker to connect. After connection, simulate a disconnect of Accessory B (e.g., power cycle or remove battery). Attempt to reconnect Accessory B by triggering the same picker flow again. Select Accessory B from the picker. Result: The accessory connects successfully at the system level. The app crashes immediately after selecting the accessory from the picker (during dismissal). Reproducibility: Occurs consistently under the described multi-accessory scenario. Not observed when only a single accessory is present.

Hi everyone, I'm developing a standalone Matter controller app on iOS 18+ using Apple's Matter.framework directly — without integrating with Apple Home or HomeKit. We manage our own Matter fabric and handle the full commissioning flow ourselves. Current setup: BLE-based Matter device discovery and commissioning via Matter.framework Own fabric management (not adding devices to Apple Home) During development, we rely on the "Bluetooth Central Matter Client Developer Mode" profile to enable BLE access The challenge: As we approach our App Store release, we need end users to be able to commission Matter devices without installing any developer profiles. I'm trying to figure out the correct entitlement path for a non-HomeKit Matter controller app in production. Questions: Which entitlements are required for a third-party Matter controller app using Matter.framework directly (not via HomeKit) to work in production? Is there a formal entitlement request process for something like com.apple.developer.matter.allow-setup-payload? If so, where do we initiate it? Are there additional program memberships or certifications required beyond the standard Apple Developer Program membership? We've gone through the Matter framework documentation and relevant WWDC sessions but haven't found a clear answer specifically for non-HomeKit standalone Matter controller apps. Would appreciate any input from Apple staff or developers who've shipped a similar app. Happy to provide more details if needed. Tagging for visibility: @Apple or relevant team — this involves a non-HomeKit Matter.framework usage pattern and entitlement approval process.

In an application we are developing, we would like to show a (non-interactable) textfield when a hardware keyboard is connected to the iPad. Therefore my question: Using SwiftUI, is it possible to detect the presence of a hardware keyboard and store that state inside a boolean like isHardwareKeyboardConnected?

I am currently developing an app for MacOS that needs to control HomeKit devices like lights. However, it seems like MacOS is supported on the official documentation, but not when I try to create an app ID on developer.apple.com. On the link https://developer.apple.com/apple-home/, MacOS is clearly showed as supported for MacOS. But when I try to create an app ID, it shows that it is only compatible for iOS, VisionOS and WatchOS. Could this be clarified? Best regards, orangeidle25