Hi, We are facing the issue of commissioning our Matter device to google home through iOS device will be 100% failed. Here is our test summary regarding the issue: TestCase1 [OK]: Commissioning our Matter 1.4.0 device to Google Nest Hub 2 by Android device (see log DoorWindow_2.0.1_Google_Success.txt ) TestCase2 [NG]: Commissioning Matter 1.4.0 device to Google Nest Hub 2 by iPhone13 or iPhone16 (see log DoorWindow_2.0.1_Google_by_iOS_NG.txt ) TestCase3 [OK]: Commissioning our Matter 1.3.0 device to Google Nest Hub 2 by iPhone13 In TestCase2, we noticed that device was first commissioned to iOS(Apple keychain) then iOS opened a commissioning window again to commission it in Google’s ecosystem, and the device was failed at above step 2, so we also tried: Commissioning the device to Apple Home works as expected, next share the device to Google Home app on iOS, this also fails. Commissioning the device to Apple Home works as expected, next share the device to Google Home app on Android, this works as expected and device pops up in Google home of iOS as well. Could you help check what's the issue of TestCase2? Append the environment of our testing: NestHub 2 version Google Home APP version

Hi, I’m developing a Matter commissioning flow and would like to clarify Apple Home’s support for concatenated (multi-device) QR codes. In my implementation, I generate a single QR code that contains multiple Matter onboarding payloads (concatenated payloads), intended to commission multiple devices in one scan, similar to a multi-pack / multi-accessory flow. What I’ve tested: Standard single-device Matter QR codes work as expected in the Apple Home app A concatenated QR code (multiple Matter payloads combined into one QR) does not get recognized / commissioned by Apple Home My questions: Does Apple Home officially support commissioning via concatenated or multi-device Matter QR codes? If yes, is there a specific payload format or delimiter that Apple Home expects? If not, is this a known limitation or something planned for future iOS/Home releases?

Hello everyone, I am developing an iOS application that relies on accelerometer data for precise motion and reaction-time measurements. Based on practical testing, it appears that third-party iOS applications receive accelerometer data at a maximum rate of approximately 100 Hz, regardless of hardware capabilities or requested update intervals. I would like to ask for clarification on the following points: Is there an officially supported way for third-party iOS apps to access accelerometer data at sampling rates higher than ~100 Hz? If the hardware supports higher sampling rates, is this limitation intentionally enforced at the iOS level for third-party applications? Are there any public APIs, entitlements, or documented approaches that allow access to higher-frequency sensor data, or is this restricted to system/internal components only? Thank you in advance for any clarification.

I followed the instructions on the page https://mfi.apple.com/en/help/login-help/How-to-Register-Your-Existing-Apple-ID.html to apply for the MFi Program. According to step 7 of the guide: "You have now created and registered your Apple Account. You will be automatically directed to the MFi Portal to begin the enrollment process," I should have been taken to the enrollment process after logging in. However, instead of accessing the enrollment page, a pop-up message appears stating: "The Apple Account you signed in with does not have permission to view this page. If you believe your company is currently enrolled in the MFi Program, please contact your company’s Account Administrator to request access to the MFi Portal. If your company is not currently enrolled in the MFi Program, please click here to learn about the program and start the enrollment process." This has created an endless loop—I cannot proceed to the enrollment process as instructed, and the pop-up only redirects me to information that leads back to the same login and permission issue. Could you please provide guidance on how to resolve this and successfully access the MFi Program enrollment process?

Summary On Mac Studio systems (no built-in camera), macOS does not initialize camera services after a normal reboot if no physical camera is present. As a result, Continuity Camera does not appear anywhere in the system. Observed behavior System Information → Camera reports “No video capture devices were found.” Continuity Camera (iPhone) is completely absent from camera lists. Plugging in any USB UVC webcam immediately initializes camera services and causes both the USB camera and the iPhone (Continuity Camera) to appear. The USB camera can then be unplugged and Continuity Camera continues working until the next reboot. Reproduction steps Use a Mac Studio (no built-in camera) on recent macOS. Ensure no USB webcam or external camera is connected. Reboot the Mac normally. After login, open System Information → Camera. Expected Camera services should initialize even when no physical camera is present, allowing Continuity Camera to be available as the primary camera. Actual No camera devices are present unless a physical USB camera is connected at least once after boot. This reproduces 100% of the time on Mac Studio and appears to be a camera service bootstrap issue where Continuity Camera cannot be the first camera device. Issue has been filed via Feedback Assistant.

Hi everyone, We are currently exploring ways to implement a frictionless Wi-Fi setup for our hardware devices without requiring a dedicated third-party application. We are interested in leveraging Apple's WAC (Wireless Accessory Configuration) to sync Wi-Fi credentials directly from iOS devices. However, we have struggled to find comprehensive technical documentation or specifications regarding the WAC service. Could anyone point us to the official source for these materials? Additionally, we have a couple of technical questions: 1.We are testing WAC provisioning and found that the Home app can discover our device and successfully get it online. However, it always ends with a "Failed to add accessory" message. Does WAC support imply that a device should be addable via the Home app? If not, why is the Home app able to discover and start the setup for a non-HomeKit WAC device? 2. Our device is already Apple AirPlay certified. Does implementing WAC require additional standalone certification, or is it covered under the existing MFi/AirPlay certification umbrella? Any insights or guidance would be greatly appreciated. Thank you!

Hello, I am a Bluetooth Engineer at Google investigating an interoperability bug between an Android device and AirPods 4. When requesting an L2CAP connection (with PSM = AVDTP) to the AirPods during SDP service discovery, The AirPods L2CAP layer incorrectly responds with a "refused - no resources available" status followed by a Pending status and a Success status. This violates the specification, which says that the request has been fully rejected after the refused status and should not receive followup responses. I suspect the "no resources available" response is a bug. This prevents A2DP from working with the AirPods. This bug does not exist with AirPods 2 firmware. Here is a packet capture: 1602 1969-12-31 16:07:04.805261 0.062473 localhost () Apple_6b:db:09 (AirPods) L2CAP 17 Sent Connection Request (AVDTP, SCID: 0x22c6) 1603 1969-12-31 16:07:04.810953 0.005692 controller host HCI_EVT 8 Rcvd Number of Completed Packets 1604 1969-12-31 16:07:04.811078 0.000125 Apple_6b:db:09 (AirPods) localhost () SDP 27 Rcvd Service Search Attribute Request : Device Information: [Bluetooth Profile Descriptor List 0x0009] 1605 1969-12-31 16:07:04.821249 0.010171 localhost () Apple_6b:db:09 (AirPods) SDP 19 Sent Service Search Attribute Response 1606 1969-12-31 16:07:04.876396 0.055147 controller host HCI_EVT 8 Rcvd Number of Completed Packets 1607 1969-12-31 16:07:04.876464 0.000068 Apple_6b:db:09 (AirPods) localhost () L2CAP 21 Rcvd Connection Response - Refused - no resources available (SCID: 0x22c6) 1608 1969-12-31 16:07:04.942539 0.066075 Apple_6b:db:09 (AirPods) localhost () SDP 41 Rcvd Service Search Attribute Request : Unknown: [Bluetooth Profile Descriptor List 0x0009] 1609 1969-12-31 16:07:04.951052 0.008513 localhost () Apple_6b:db:09 (AirPods) SDP 19 Sent Service Search Attribute Response 1610 1969-12-31 16:07:05.010605 0.059553 controller host HCI_EVT 8 Rcvd Number of Completed Packets 1611 1969-12-31 16:07:05.080593 0.069988 Apple_6b:db:09 (AirPods) localhost () SDP 27 Rcvd Service Search Attribute Request : GATT: [Bluetooth Profile Descriptor List 0x0009] 1612 1969-12-31 16:07:05.087636 0.007043 localhost () Apple_6b:db:09 (AirPods) SDP 19 Sent Service Search Attribute Response 1613 1969-12-31 16:07:05.209417 0.121781 controller host HCI_EVT 8 Rcvd Number of Completed Packets 1614 1969-12-31 16:07:05.279491 0.070074 Apple_6b:db:09 (AirPods) localhost () L2CAP 21 Rcvd Connection Response - Pending (SCID: 0x22c6) 1615 1969-12-31 16:07:05.280731 0.001240 Apple_6b:db:09 (AirPods) localhost () L2CAP 21 Rcvd Connection Response - Success (SCID: 0x22c6, DCID: 0x0406) Please file this bug with the AirPods Bluetooth team.

Is there any way to use AccessorySetupKit in the background to discover BLE devices?

I'm developing an iPad app and encountered a strange issue with external Bluetooth keyboards. Issue: I have a Bluetooth keyboard set to JIS layout in Settings > General > Keyboard > Hardware Keyboard > Keyboard Type. If I connect the keyboard before launching the app, everything works fine, and the input follows the JIS layout. However, if I launch the app first and then turn on the Bluetooth keyboard, the input behaves as if the keyboard is in ANSI layout, even though the settings still show JIS. It seems like iPadOS defaults to ANSI if no external keyboard is connected when the app starts, and later connections do not update the layout properly. Has anyone encountered a similar issue, and is there a programmatic way to ensure that the correct keyboard layout is applied after the keyboard is connected? Any help or insights would be greatly appreciated!

Hi, We’re developing a BLE peripheral device and encountered a connection issue when connecting two devices (Device A and Device B) simultaneously to an iOS device. Problem: On iOS 18, we are experiencing occasional BLE timeouts and disconnections when both devices are connected at the same time. On iOS 16, we did not encounter this issue under the same conditions. What we’ve tried: Adjusted the connection interval from 30ms to 15ms. This seems to have improved stability somewhat. However, we still observe intermittent timeout/disconnection issues. Questions: Are there any known changes in BLE connection handling or timing constraints in iOS 18? Are there recommended connection parameter settings (interval, latency, timeout, etc.) for multi-device BLE connections in iOS? Is there a way to debug or log more details about the disconnection reasons on the iOS side? Any guidance or suggestions would be greatly appreciated.

Hi there, I am using Core NFC and I established the connection with the card, but after sending the command 'tag.sendCommand()' I receive this message: -[NFCTagReaderSession _connectTag:error:]:748 Error Domain=NFCError Code=2 "Missing required entitlement" UserInfo={NSLocalizedDescription=Missing required entitlement}. The version of XCode I am using is 16.3, and the iPhone version is iOS 18.4 Here is my entitlements file: com.apple.developer.nfc.readersession.formats NDEF TAG And my info.plist: NFCReaderUsageDescription NFC com.apple.developer.nfc.readersession.iso7816.select-identifiers A000112233445566 Signing & Capabilities‌ has added Near Field Communication Tag Reading‌.

We are integrating the Microsoft Web Chat Control inside a WKWebView in our iOS application. The microphone button (used for speech input) works as expected when the app is active. However, we are facing an issue when the app is sent to the background and then brought back to the foreground. Issue Details: When the app returns from background to foreground: 🔹 The mic button becomes unresponsive (taps are not recognized). 🔹 No permission prompt or speech functionality is triggered. 🔹 Other elements of the Web Chat control continue to work fine. This issue seems isolated to iOS and WKWebView usage. We have verified that microphone permissions are granted and there are no system-level blocks. Environment: Platform: iOS Web Container: WKWebView Microsoft Web Chat Version: Devanshu Kinariwala add version here iOS Version: iOS 18.3.1 Devices: iPhone 13, iPhone 14 Pro error in browser console [Error] A MediaStreamTrack ended due to a capture failure (x3) [Error] WebSocket connection to 'wss://directline.botframework.com/v3/directline/conversations/JQ1k0phVogeJ30ZQddBvAQ-in/stream?watermark=-&t=eyJhbGciOiJSUzI1NiIsImtpZCI6ImlmOEs0aFg4R1hXVnZkS3pwdFRFWFJveURTUSIsIng1dCI6ImlmOEs0aFg4R1hXVnZkS3pwdFRFWFJveURTUSIsInR5cCI6IkpXVCJ9.eyJib3QiOiJhaWFhcy1xYS1jb252YWktYm90Iiwic2l0ZSI6InRWcW14cDBQZU9vIiwiY29udiI6IkpRMWswcGhWb2dlSjMwWlFkZEJ2QVEtaW4iLCJuYmYiOjE3NDI5NzE1MTgsImV4cCI6MTc0Mjk3MTU3OCwiaXNzIjoiaHR0cHM6Ly9kaXJlY3RsaW5lLmJvdGZyYW1ld29yay5jb20vIiwiYXVkIjoiaHR0cHM6Ly9kaXJlY3RsaW5lLmJvdGZyYW1ld29yay5jb20vIn0.Mx3MMVP3t9Ex36UW-YARskZLny0iORxc6-B0ewvNp0S-ivUjvOS43kZc0J5HoOgYRkoGaKemo00_JSkzryAbKKoSwqMjahf0VotqTZsJjoIgtyNJFfAYyGVriBHMV_6FfH_YEezDMD5puY6R89eM-atQOw-CfoClwrxn8jgVL5Kn19WdDZvmQwFIArklA7as8bboKcWv4PveEKptM9xCokttaGzv-S5pdbNETMoJzIhLcJDHmEVJ6oJ0TFs5XS7RGMSQlM_gs95TySzVjVL7XV6qEOt_A10lRzmx0PxPIUw_nqllEIbWFy5H7AfsxbKRtM1nLe4lRm1KS7_xw9dSlw' failed: The operation couldn’t be completed. Software caused connection abort [Error] WebSocket connection to 'wss://eastus2.stt.speech.microsoft.com/speech/recognition/conversation/cognitiveservices/v1?language=en-US&format=detailed&Ocp-Apim-Subscription-Key=4JuKqIMwLMhgAxfORVDEYfiuTL6Hrbnj3isAeGfs7aks4AOltun6JQQJ99AKACHYHv6XJ3w3AAAYACOGJFYj&X-ConnectionId=A93B097C62F14C55B30A851798609F73' failed: The operation couldn’t be completed. Software caused connection abort [Error] WebSocket connection to 'wss://eastus2.stt.speech.microsoft.com/speech/recognition/conversation/cognitiveservices/v1?language=en-US&format=detailed&Ocp-Apim-Subscription-Key=4JuKqIMwLMhgAxfORVDEYfiuTL6Hrbnj3isAeGfs7aks4AOltun6JQQJ99AKACHYHv6XJ3w3AAAYACOGJFYj&X-ConnectionId=E99DF3A6CE734E0294A5FB5296D725CC' failed: The operation couldn’t be completed. Software caused connection abort [Error] WebSocket connection to 'wss://eastus2.stt.speech.microsoft.com/speech/recognition/conversation/cognitiveservices/v1?language=en-US&format=detailed&Ocp-Apim-Subscription-Key=4JuKqIMwLMhgAxfORVDEYfiuTL6Hrbnj3isAeGfs7aks4AOltun6JQQJ99AKACHYHv6XJ3w3AAAYACOGJFYj&X-ConnectionId=8B3370005E7A4946BEA174E804F64FF7' failed: The operation couldn’t be completed. Software caused connection abort Swift: // Method to check microphone permission func checkMicrophonePermission(completion: @escaping (Bool) -> Void) { let authorizationStatus = AVCaptureDevice.authorizationStatus(for: .audio) switch authorizationStatus { case .authorized: // Permission granted completion(true) case .notDetermined: // Request permission AVCaptureDevice.requestAccess(for: .audio) { granted in DispatchQueue.main.async { completion(granted) } } case .denied, .restricted: // Permission denied or restricted completion(false) @unknown default: // Handle future cases completion(false) } }

I want to get Cover-Art Image over Bluetooth. From the SDP Discover iPhoneSE, it support Cover-Art Feature. I connect and config OBEX Channel with L2CAP ERTM, it is successful. I send connect_request the OBEX Connect, the iPhone always no any response, and l2cap s-frame response from iPhone always failed. From the Apple Developer, it need Apple Authentication Chip. Is it still necessary now? Are there any other ways to obtain album pictures?

Hey, I need to know how to use texture mapping for rendering a spectrogram in metal. As I need smoothens the spectrogram. In my current project I am using vertex based approach which results in blocky behaviour between each quad. I need to smooth across each qaud so that It will smoothly gradient over.

Hello, I recently installed the macOS 26 beta version on my MacBook Air M3, and I've encountered an issue where edited Word files are failing to save. I’ve tried restarting my laptop and checking for updates, but the problem persists. Has anyone else experienced this issue? Is there a specific setting I might have missed or any troubleshooting steps you recommend? Thank you for your assistance!

The battery drains quickly on iPhone SE 3. Whenever I take it off the charger it drains from 100% to 80% in 20 minutes. Please fix this bug?

Recently I got an issue on App Store that my build got rejected because of iPad Air 5. My app include Device binding which means sim should be present in Device while using the app, where as, I mad the app mainly for iPhone not for pads. But AppStore is rejecting my build saying getting no sim issue in iPad Air 5th gen And os 18.5 . So what should I do? Which device I should prefer so that I can use it future also , should not be outdated within some time.

Hi there! I'm developing a dual-mode bluetooth accessory and would like to pair it through AccessorySetupKit. I'm using an ESP32 with Bluekitchen btstack. This supports CTKD, which seems to be a requirement for the Bluetooth transport bridging according the WWDC19 session 901. I've been in contact with the btstack developer and verified that I can get the device to generate an LTK for the classic transport when reading an encrypted attribute. I'm not able to get this to work with the bluetoothTransportBriding option with AccessorySetupKit though. What I've found so far is that if I omit the .bluetoothTransportBriding option during pairing I will get a pairing request when I read an encrypted attribute after connecting with the CBConnectPeripheralOptionEnableTransportBridgingKey option. If I accept this request it seems like the system automatically brings up the A2DP profile. However if I include .bluetoothTransportBriding and/or .bluetoothPairingLE this option does not pop up, but the system does not bring up the A2DP profile. In this case things seem to end up in a weird situation where the device doesn't show up for pairing in Bluetooth Settings either, making it impossible to manually connect for A2DP. Based on the AccessorySetupKit example from WWDC24 I've created a dice accessory firmware for ESP32 using btstack. The code for this is available here: https://github.com/ljodal/esp32-btstack-ctkd-test I've also tweaked the AccessorySetupKit example app for iOS to add the ASAccessory.SupportOptions. The code for that is available here: https://github.com/ljodal/accessorysetupkit-ctkd-test Is there any documentation available anywhere on what is expected of the device for Bluetooth Transport Bridging to work with AccessorySetupKit?

first post here and this is kinda a long shot. I’m working on a custom keypad project for a young man with some mobility issues that unfortunately prevents gestrue and voice control as UI options. id like to see if I can pull track metadata via a Bluetooth connection into a custom keyboard with a small screen. I know hid doesn’t support this but I was hoping maybe the API for iOS’s blueprint remote app could be leveraged. I haven’t don’t much with Apple previousl. Usually Roku and Crestron implantations but I’m hoping to see if I can accomplish something with Apple, without needing to implement any IP connection.

Our app is connected to a hardware wifi without network. Under normal circumstances, we can communicate with the device. At some point, the communication suddenly stops, and the ping prompts "No route to host". The only way to reconnect is to restart the device. It feels like the system has marked ARP. Is there any way to reconnect the device without restarting the iphone?